Add submodule dependency filesHEADmaster

Change-Id: Iaf8d18082d3991dec7c0ebbea540f092188eb4ec

1 files changed, 579 insertions, 0 deletions

diff --git a/roms/u-boot/doc/board/sifive/unleashed.rst b/roms/u-boot/doc/board/sifive/unleashed.rst
new file mode 100644
index 000000000..4e4c852ff
--- /dev/null
+++ b/roms/u-boot/doc/board/sifive/unleashed.rst
@@ -0,0 +1,579 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+HiFive Unleashed
+================
+
+FU540-C000 RISC-V SoC
+---------------------
+The FU540-C000 is the world’s first 4+1 64-bit RISC-V SoC from SiFive.
+
+The HiFive Unleashed development platform is based on FU540-C000 and capable
+of running Linux.
+
+Mainline support
+----------------
+
+The support for following drivers are already enabled:
+
+1. SiFive UART Driver.
+2. SiFive PRCI Driver for clock.
+3. Cadence MACB ethernet driver for networking support.
+4. SiFive SPI Driver.
+5. MMC SPI Driver for MMC/SD support.
+
+Booting from MMC using FSBL
+---------------------------
+
+Building
+~~~~~~~~
+
+1. Add the RISC-V toolchain to your PATH.
+2. Setup ARCH & cross compilation environment variable:
+
+.. code-block:: none
+
+   export CROSS_COMPILE=<riscv64 toolchain prefix>
+
+3. make sifive_fu540_defconfig
+4. make
+
+Flashing
+~~~~~~~~
+
+The current U-Boot port is supported in S-mode only and loaded from DRAM.
+
+A prior stage M-mode firmware/bootloader (e.g OpenSBI) is required to
+boot the u-boot.bin in S-mode and provide M-mode runtime services.
+
+Currently, the u-boot.bin is used as a payload of the OpenSBI FW_PAYLOAD
+firmware. We need to compile OpenSBI with below command:
+
+.. code-block:: none
+
+	make PLATFORM=generic FW_PAYLOAD_PATH=<path to u-boot-dtb.bin>
+
+More detailed description of steps required to build FW_PAYLOAD firmware
+is beyond the scope of this document. Please refer OpenSBI documenation.
+(Note: OpenSBI git repo is at https://github.com/riscv/opensbi.git)
+
+Once the prior stage firmware/bootloader binary is generated, it should be
+copied to the first partition of the sdcard.
+
+.. code-block:: none
+
+    sudo dd if=<prior_stage_firmware_binary> of=/dev/disk2s1 bs=1024
+
+Booting
+~~~~~~~
+
+Once you plugin the sdcard and power up, you should see the U-Boot prompt.
+
+Sample boot log from HiFive Unleashed board
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+.. code-block:: none
+
+   U-Boot 2019.07-00024-g350ff02f5b (Jul 22 2019 - 11:45:02 +0530)
+
+   CPU:   rv64imafdc
+   Model: SiFive HiFive Unleashed A00
+   DRAM:  8 GiB
+   MMC:   spi@10050000:mmc@0: 0
+   In:    serial@10010000
+   Out:   serial@10010000
+   Err:   serial@10010000
+   Net:   eth0: ethernet@10090000
+   Hit any key to stop autoboot:  0
+   => version
+   U-Boot 2019.07-00024-g350ff02f5b (Jul 22 2019 - 11:45:02 +0530)
+
+   riscv64-linux-gcc.br_real (Buildroot 2018.11-rc2-00003-ga0787e9) 8.2.0
+   GNU ld (GNU Binutils) 2.31.1
+   => mmc info
+   Device: spi@10050000:mmc@0
+   Manufacturer ID: 3
+   OEM: 5344
+   Name: SU08G
+   Bus Speed: 20000000
+   Mode: SD Legacy
+   Rd Block Len: 512
+   SD version 2.0
+   High Capacity: Yes
+   Capacity: 7.4 GiB
+   Bus Width: 1-bit
+   Erase Group Size: 512 Bytes
+   => mmc part
+
+   Partition Map for MMC device 0  --   Partition Type: EFI
+
+   Part    Start LBA       End LBA         Name
+           Attributes
+           Type GUID
+           Partition GUID
+     1     0x00000800      0x000107ff      "bootloader"
+           attrs:  0x0000000000000000
+           type:   2e54b353-1271-4842-806f-e436d6af6985
+           guid:   393bbd36-7111-491c-9869-ce24008f6403
+     2     0x00040800      0x00ecdfde      ""
+           attrs:  0x0000000000000000
+           type:   0fc63daf-8483-4772-8e79-3d69d8477de4
+           guid:   7fc9a949-5480-48c7-b623-04923080757f
+
+Now you can configure your networking, tftp server and use tftp boot method to
+load uImage.
+
+.. code-block:: none
+
+   => setenv ipaddr 10.206.7.133
+   => setenv netmask 255.255.252.0
+   => setenv serverip 10.206.4.143
+   => setenv gateway 10.206.4.1
+
+If you want to use a flat kernel image such as Image file
+
+.. code-block:: none
+
+   => tftpboot ${kernel_addr_r} /sifive/fu540/Image
+   ethernet@10090000: PHY present at 0
+   ethernet@10090000: Starting autonegotiation...
+   ethernet@10090000: Autonegotiation complete
+   ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x3c00)
+   Using ethernet@10090000 device
+   TFTP from server 10.206.4.143; our IP address is 10.206.7.133
+   Filename '/sifive/fu540/Image'.
+   Load address: 0x84000000
+   Loading: #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            ##########################################
+            1.2 MiB/s
+   done
+   Bytes transferred = 8867100 (874d1c hex)
+
+Or if you want to use a compressed kernel image file such as Image.gz
+
+.. code-block:: none
+
+   => tftpboot ${kernel_addr_r} /sifive/fu540/Image.gz
+   ethernet@10090000: PHY present at 0
+   ethernet@10090000: Starting autonegotiation...
+   ethernet@10090000: Autonegotiation complete
+   ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x3c00)
+   Using ethernet@10090000 device
+   TFTP from server 10.206.4.143; our IP address is 10.206.7.133
+   Filename '/sifive/fu540/Image.gz'.
+   Load address: 0x84000000
+   Loading: #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            ##########################################
+            1.2 MiB/s
+   done
+   Bytes transferred = 4809458 (4962f2 hex)
+   =>setenv kernel_comp_addr_r 0x90000000
+   =>setenv kernel_comp_size 0x500000
+
+By this time, correct kernel image is loaded and required environment variables
+are set. You can proceed to load the ramdisk and device tree from the tftp server
+as well.
+
+.. code-block:: none
+
+   => tftpboot ${ramdisk_addr_r} /sifive/fu540/uRamdisk
+   ethernet@10090000: PHY present at 0
+   ethernet@10090000: Starting autonegotiation...
+   ethernet@10090000: Autonegotiation complete
+   ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x3c00)
+   Using ethernet@10090000 device
+   TFTP from server 10.206.4.143; our IP address is 10.206.7.133
+   Filename '/sifive/fu540/uRamdisk'.
+   Load address: 0x88300000
+   Loading: #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            #################################################################
+            ##############
+            418.9 KiB/s
+   done
+   Bytes transferred = 2398272 (249840 hex)
+   => tftpboot ${fdt_addr_r} /sifive/fu540/hifive-unleashed-a00.dtb
+   ethernet@10090000: PHY present at 0
+   ethernet@10090000: Starting autonegotiation...
+   ethernet@10090000: Autonegotiation complete
+   ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x7c00)
+   Using ethernet@10090000 device
+   TFTP from server 10.206.4.143; our IP address is 10.206.7.133
+   Filename '/sifive/fu540/hifive-unleashed-a00.dtb'.
+   Load address: 0x88000000
+   Loading: ##
+            1000 Bytes/s
+   done
+   Bytes transferred = 5614 (15ee hex)
+   => setenv bootargs "root=/dev/ram rw console=ttySIF0 ip=dhcp earlycon=sbi"
+   => booti ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}
+   ## Loading init Ramdisk from Legacy Image at 88300000 ...
+      Image Name:   Linux RootFS
+      Image Type:   RISC-V Linux RAMDisk Image (uncompressed)
+      Data Size:    2398208 Bytes = 2.3 MiB
+      Load Address: 00000000
+      Entry Point:  00000000
+      Verifying Checksum ... OK
+   ## Flattened Device Tree blob at 88000000
+      Booting using the fdt blob at 0x88000000
+      Using Device Tree in place at 0000000088000000, end 00000000880045ed
+
+   Starting kernel ...
+
+   [    0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
+   [    0.000000] Linux version 5.3.0-rc1-00003-g460ac558152f (anup@anup-lab-machine) (gcc version 8.2.0 (Buildroot 2018.11-rc2-00003-ga0787e9)) #6 SMP Mon Jul 22 10:01:01 IST 2019
+   [    0.000000] earlycon: sbi0 at I/O port 0x0 (options '')
+   [    0.000000] printk: bootconsole [sbi0] enabled
+   [    0.000000] Initial ramdisk at: 0x(____ptrval____) (2398208 bytes)
+   [    0.000000] Zone ranges:
+   [    0.000000]   DMA32    [mem 0x0000000080200000-0x00000000ffffffff]
+   [    0.000000]   Normal   [mem 0x0000000100000000-0x000000027fffffff]
+   [    0.000000] Movable zone start for each node
+   [    0.000000] Early memory node ranges
+   [    0.000000]   node   0: [mem 0x0000000080200000-0x000000027fffffff]
+   [    0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000027fffffff]
+   [    0.000000] software IO TLB: mapped [mem 0xfbfff000-0xfffff000] (64MB)
+   [    0.000000] CPU with hartid=0 is not available
+   [    0.000000] CPU with hartid=0 is not available
+   [    0.000000] elf_hwcap is 0x112d
+   [    0.000000] percpu: Embedded 18 pages/cpu s34584 r8192 d30952 u73728
+   [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 2067975
+   [    0.000000] Kernel command line: root=/dev/ram rw console=ttySIF0 ip=dhcp earlycon=sbi
+   [    0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
+   [    0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
+   [    0.000000] Sorting __ex_table...
+   [    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
+   [    0.000000] Memory: 8182308K/8386560K available (5916K kernel code, 368K rwdata, 1840K rodata, 213K init, 304K bss, 204252K reserved, 0K cma-reserved)
+   [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
+   [    0.000000] rcu: Hierarchical RCU implementation.
+   [    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
+   [    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
+   [    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
+   [    0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
+   [    0.000000] plic: mapped 53 interrupts with 4 handlers for 9 contexts.
+   [    0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1]
+   [    0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
+   [    0.000006] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns
+   [    0.008559] Console: colour dummy device 80x25
+   [    0.012989] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=4000)
+   [    0.023104] pid_max: default: 32768 minimum: 301
+   [    0.028273] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
+   [    0.035765] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
+   [    0.045307] rcu: Hierarchical SRCU implementation.
+   [    0.049875] smp: Bringing up secondary CPUs ...
+   [    0.055729] smp: Brought up 1 node, 4 CPUs
+   [    0.060599] devtmpfs: initialized
+   [    0.064819] random: get_random_u32 called from bucket_table_alloc.isra.10+0x4e/0x160 with crng_init=0
+   [    0.073720] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
+   [    0.083176] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
+   [    0.090721] NET: Registered protocol family 16
+   [    0.106319] vgaarb: loaded
+   [    0.108670] SCSI subsystem initialized
+   [    0.112515] usbcore: registered new interface driver usbfs
+   [    0.117758] usbcore: registered new interface driver hub
+   [    0.123167] usbcore: registered new device driver usb
+   [    0.128905] clocksource: Switched to clocksource riscv_clocksource
+   [    0.141239] NET: Registered protocol family 2
+   [    0.145506] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
+   [    0.153754] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
+   [    0.163466] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
+   [    0.173468] TCP: Hash tables configured (established 65536 bind 65536)
+   [    0.179739] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
+   [    0.186627] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
+   [    0.194117] NET: Registered protocol family 1
+   [    0.198417] RPC: Registered named UNIX socket transport module.
+   [    0.203887] RPC: Registered udp transport module.
+   [    0.208664] RPC: Registered tcp transport module.
+   [    0.213429] RPC: Registered tcp NFSv4.1 backchannel transport module.
+   [    0.219944] PCI: CLS 0 bytes, default 64
+   [    0.224170] Unpacking initramfs...
+   [    0.262347] Freeing initrd memory: 2336K
+   [    0.266531] workingset: timestamp_bits=62 max_order=21 bucket_order=0
+   [    0.280406] NFS: Registering the id_resolver key type
+   [    0.284798] Key type id_resolver registered
+   [    0.289048] Key type id_legacy registered
+   [    0.293114] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
+   [    0.300262] NET: Registered protocol family 38
+   [    0.304432] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
+   [    0.311862] io scheduler mq-deadline registered
+   [    0.316461] io scheduler kyber registered
+   [    0.356421] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
+   [    0.363004] 10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 4, base_baud = 0) is a SiFive UART v0
+   [    0.371468] printk: console [ttySIF0] enabled
+   [    0.371468] printk: console [ttySIF0] enabled
+   [    0.380223] printk: bootconsole [sbi0] disabled
+   [    0.380223] printk: bootconsole [sbi0] disabled
+   [    0.389589] 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 1, base_baud = 0) is a SiFive UART v0
+   [    0.398680] [drm] radeon kernel modesetting enabled.
+   [    0.412395] loop: module loaded
+   [    0.415214] sifive_spi 10040000.spi: mapped; irq=3, cs=1
+   [    0.420628] sifive_spi 10050000.spi: mapped; irq=5, cs=1
+   [    0.425897] libphy: Fixed MDIO Bus: probed
+   [    0.429964] macb 10090000.ethernet: Registered clk switch 'sifive-gemgxl-mgmt'
+   [    0.436743] macb: GEM doesn't support hardware ptp.
+   [    0.441621] libphy: MACB_mii_bus: probed
+   [    0.601316] Microsemi VSC8541 SyncE 10090000.ethernet-ffffffff:00: attached PHY driver [Microsemi VSC8541 SyncE] (mii_bus:phy_addr=10090000.ethernet-ffffffff:00, irq=POLL)
+   [    0.615857] macb 10090000.ethernet eth0: Cadence GEM rev 0x10070109 at 0x10090000 irq 6 (70:b3:d5:92:f2:f3)
+   [    0.625634] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
+   [    0.631381] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
+   [    0.637382] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
+   [    0.643799] ehci-pci: EHCI PCI platform driver
+   [    0.648261] ehci-platform: EHCI generic platform driver
+   [    0.653497] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
+   [    0.659599] ohci-pci: OHCI PCI platform driver
+   [    0.664055] ohci-platform: OHCI generic platform driver
+   [    0.669448] usbcore: registered new interface driver uas
+   [    0.674575] usbcore: registered new interface driver usb-storage
+   [    0.680642] mousedev: PS/2 mouse device common for all mice
+   [    0.709493] mmc_spi spi1.0: SD/MMC host mmc0, no DMA, no WP, no poweroff, cd polling
+   [    0.716615] usbcore: registered new interface driver usbhid
+   [    0.722023] usbhid: USB HID core driver
+   [    0.726738] NET: Registered protocol family 10
+   [    0.731359] Segment Routing with IPv6
+   [    0.734332] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
+   [    0.740687] NET: Registered protocol family 17
+   [    0.744660] Key type dns_resolver registered
+   [    0.806775] mmc0: host does not support reading read-only switch, assuming write-enable
+   [    0.814020] mmc0: new SDHC card on SPI
+   [    0.820137] mmcblk0: mmc0:0000 SU08G 7.40 GiB
+   [    0.850220]  mmcblk0: p1 p2
+   [    3.821524] macb 10090000.ethernet eth0: link up (1000/Full)
+   [    3.828938] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
+   [    3.848919] Sending DHCP requests .., OK
+   [    6.252076] IP-Config: Got DHCP answer from 10.206.4.1, my address is 10.206.7.133
+   [    6.259624] IP-Config: Complete:
+   [    6.262831]      device=eth0, hwaddr=70:b3:d5:92:f2:f3, ipaddr=10.206.7.133, mask=255.255.252.0, gw=10.206.4.1
+   [    6.272809]      host=dhcp-10-206-7-133, domain=sdcorp.global.sandisk.com, nis-domain=(none)
+   [    6.281228]      bootserver=10.206.126.11, rootserver=10.206.126.11, rootpath=
+   [    6.281232]      nameserver0=10.86.1.1, nameserver1=10.86.2.1
+   [    6.294179]      ntpserver0=10.86.1.1, ntpserver1=10.86.2.1
+   [    6.301026] Freeing unused kernel memory: 212K
+   [    6.304683] This architecture does not have kernel memory protection.
+   [    6.311121] Run /init as init process
+              _  _
+             | ||_|
+             | | _ ____  _   _  _  _
+             | || |  _ \| | | |\ \/ /
+             | || | | | | |_| |/    \
+             |_||_|_| |_|\____|\_/\_/
+
+                  Busybox Rootfs
+
+   Please press Enter to activate this console.
+   / #
+
+Booting from MMC using U-Boot SPL
+---------------------------------
+
+Building
+~~~~~~~~
+
+Before building U-Boot SPL, OpenSBI must be built first. OpenSBI can be
+cloned and built for FU540 as below:
+
+.. code-block:: console
+
+	git clone https://github.com/riscv/opensbi.git
+	cd opensbi
+	make PLATFORM=generic
+	export OPENSBI=<path to opensbi/build/platform/generic/firmware/fw_dynamic.bin>
+
+Now build the U-Boot SPL and U-Boot proper
+
+.. code-block:: console
+
+	cd <U-Boot-dir>
+	make sifive_fu540_defconfig
+	make
+
+This will generate spl/u-boot-spl.bin and FIT image (u-boot.itb)
+
+
+Flashing
+~~~~~~~~
+
+ZSBL loads the U-Boot SPL (u-boot-spl.bin) from a partition with GUID type
+5B193300-FC78-40CD-8002-E86C45580B47
+
+U-Boot SPL expects a U-Boot FIT image (u-boot.itb) from a partition with GUID
+type 2E54B353-1271-4842-806F-E436D6AF6985
+
+FIT image (u-boot.itb) is a combination of fw_dynamic.bin, u-boot-nodtb.bin and
+device tree blob (hifive-unleashed-a00.dtb)
+
+Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch)
+
+.. code-block:: none
+
+	# sudo sgdisk --clear \
+	> --set-alignment=2 \
+	> --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
+	> --new=2:2082:10273 --change-name=2:loader2 --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
+	> --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \
+	> /dev/sda
+
+Program the SD card
+
+.. code-block:: none
+
+	sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
+	sudo dd if=u-boot.itb of=/dev/sda seek=2082
+
+Booting
+~~~~~~~
+
+Once you plugin the sdcard and power up, you should see the U-Boot prompt.
+
+Sample boot log from HiFive Unleashed board
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+.. code-block:: none
+
+	U-Boot SPL 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
+	Trying to boot from MMC1
+
+
+	U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
+
+	CPU:   rv64imafdc
+	Model: SiFive HiFive Unleashed A00
+	DRAM:  8 GiB
+	MMC:   spi@10050000:mmc@0: 0
+	In:    serial@10010000
+	Out:   serial@10010000
+	Err:   serial@10010000
+	Net:   eth0: ethernet@10090000
+	Hit any key to stop autoboot:  0
+	=> version
+	U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
+
+	riscv64-unknown-linux-gnu-gcc (crosstool-NG 1.24.0.37-3f461da) 9.2.0
+	GNU ld (crosstool-NG 1.24.0.37-3f461da) 2.32
+	=> mmc info
+	Device: spi@10050000:mmc@0
+	Manufacturer ID: 3
+	OEM: 5344
+	Name: SC16G
+	Bus Speed: 20000000
+	Mode: SD Legacy
+	Rd Block Len: 512
+	SD version 2.0
+	High Capacity: Yes
+	Capacity: 14.8 GiB
+	Bus Width: 1-bit
+	Erase Group Size: 512 Bytes
+	=> mmc part
+
+	Partition Map for MMC device 0  --   Partition Type: EFI
+
+	Part    Start LBA       End LBA         Name
+	Attributes
+	Type GUID
+	Partition GUID
+	1     0x00000022      0x00000821      "loader1"
+	attrs:  0x0000000000000000
+	type:   5b193300-fc78-40cd-8002-e86c45580b47
+	guid:   66e2b5d2-74db-4df8-ad6f-694b3617f87f
+	2     0x00000822      0x00002821      "loader2"
+	attrs:  0x0000000000000000
+	type:   2e54b353-1271-4842-806f-e436d6af6985
+	guid:   8befaeaf-bca0-435d-b002-e201f37c0a2f
+	3     0x00002822      0x01dacbde      "rootfs"
+	attrs:  0x0000000000000000
+	type:   0fc63daf-8483-4772-8e79-3d69d8477de4
+	type:   linux
+	guid:   9faa81b6-39b1-4418-af5e-89c48f29c20d
+
+Booting from SPI
+----------------
+
+Use Building steps from "Booting from MMC using U-Boot SPL" section.
+
+Partition the SPI in Linux via mtdblock. (Require to boot the board in
+SD boot mode by enabling MTD block in Linux)
+
+Use prebuilt image from here [1], which support to partition the SPI flash.
+
+.. code-block:: none
+
+  # sgdisk --clear \
+  > --set-alignment=2 \
+  > --new=1:40:2087 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
+  > --new=2:2088:10279 --change-name=2:loader2 --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
+  > --new=3:10536:65494 --change-name=3:rootfs --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \
+  > /dev/mtdblock0
+
+Program the SPI (Require to boot the board in SD boot mode)
+
+Execute below steps on U-Boot proper,
+
+.. code-block:: none
+
+  tftpboot $kernel_addr_r u-boot-spl.bin
+  sf erase 0x5000 $filesize
+  sf write $kernel_addr_r 0x5000 $filesize
+
+  tftpboot $kernel_addr_r u-boot.itb
+  sf erase 0x105000 $filesize
+  sf write $kernel_addr_r 0x105000 $filesize
+
+Power off the board
+
+Change DIP switches MSEL[3:0] are set to 0110
+
+Power up the board.
+
+[1] https://github.com/amarula/bsp-sifive