diff options
Diffstat (limited to 'roms/u-boot/board/freescale/t104xrdb/README')
| -rw-r--r-- | roms/u-boot/board/freescale/t104xrdb/README | 386 |
1 files changed, 386 insertions, 0 deletions
diff --git a/roms/u-boot/board/freescale/t104xrdb/README b/roms/u-boot/board/freescale/t104xrdb/README new file mode 100644 index 000000000..09cb98e33 --- /dev/null +++ b/roms/u-boot/board/freescale/t104xrdb/README @@ -0,0 +1,386 @@ +Overview +-------- +The T1040RDB is a Freescale reference board that hosts the T1040 SoC +(and variants). Variants inclued T1042 presonality of T1040, in which +case T1040RDB can also be called T1042RDB. + +The T1042RDB is a Freescale reference board that hosts the T1042 SoC +(and variants). The board is similar to T1040RDB, T1040 is a reduced +personality of T1040 SoC without Integrated 8-port Gigabit(L2 Switch). + +The T1042RDB_PI is a Freescale reference board that hosts the T1042 SoC. +(a personality of T1040 SoC). The board is similar to T1040RDB but is +designed specially with low power features targeted for Printing Image Market. + +The T1040D4RDB is a Freescale reference board that hosts the T1040 SoC. +The board is re-designed T1040RDB board with following changes : + - Support of DDR4 memory and some enhancements + +The T1042D4RDB is a Freescale reference board that hosts the T1042 SoC. +The board is re-designed T1040RDB board with following changes : + - Support of DDR4 memory + - Support for 0x86 serdes protocol which can support following interfaces + - 2 RGMII's on DTSEC4, DTSEC5 + - 3 SGMII on DTSEC1, DTSEC2 & DTSEC3 + +Basic difference's among T1040RDB, T1042RDB_PI, T1042RDB +------------------------------------------------------------------------- +Board Si Protocol Targeted Market +------------------------------------------------------------------------- +T1040RDB T1040 0x66 Networking +T1040RDB T1042 0x86 Networking +T1042RDB_PI T1042 0x06 Printing & Imaging +T1040D4RDB T1040 0x66 Networking +T1042D4RDB T1042 0x86 Networking + + +T1040 SoC Overview +------------------ +The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA +processor cores with high-performance data path acceleration architecture +and network peripheral interfaces required for networking & telecommunications. + +The T1040/T1042 SoC includes the following function and features: + + - Four e5500 cores, each with a private 256 KB L2 cache + - 256 KB shared L3 CoreNet platform cache (CPC) + - Interconnect CoreNet platform + - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving + support + - Data Path Acceleration Architecture (DPAA) incorporating acceleration + for the following functions: + - Packet parsing, classification, and distribution + - Queue management for scheduling, packet sequencing, and congestion + management + - Cryptography Acceleration (SEC 5.0) + - RegEx Pattern Matching Acceleration (PME 2.2) + - IEEE Std 1588 support + - Hardware buffer management for buffer allocation and deallocation + - Ethernet interfaces + - Integrated 8-port Gigabit Ethernet switch (T1040 only) + - Four 1 Gbps Ethernet controllers + - Two RGMII interfaces or one RGMII and one MII interfaces + - High speed peripheral interfaces + - Four PCI Express 2.0 controllers running at up to 5 GHz + - Two SATA controllers supporting 1.5 and 3.0 Gb/s operation + - Upto two QSGMII interface + - Upto six SGMII interface supporting 1000 Mbps + - One SGMII interface supporting upto 2500 Mbps + - Additional peripheral interfaces + - Two USB 2.0 controllers with integrated PHY + - SD/eSDHC/eMMC + - eSPI controller + - Four I2C controllers + - Four UARTs + - Four GPIO controllers + - Integrated flash controller (IFC) + - LCD and HDMI interface (DIU) with 12 bit dual data rate + - TDM interface + - Multicore programmable interrupt controller (PIC) + - Two 8-channel DMA engines + - Single source clocking implementation + - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) + +T1040 SoC Personalities +------------------------- +T1022 Personality: +T1022 is a reduced personality of T1040 with less core/clusters. + +T1042 Personality: +T1042 is a reduced personality of T1040 without Integrated 8-port Gigabit +Ethernet switch. Rest of the blocks are same as T1040 + + +T1040RDB board Overview +------------------------- + - SERDES Connections, 8 lanes information: + 1: None + 2: SGMII + 3: QSGMII + 4: QSGMII + 5: PCIe1 x1 slot + 6: mini PCIe connector + 7: mini PCIe connector + 8: SATA connector + - DDR Controller + - Supports rates of up to 1600 MHz data-rate + - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types. + - IFC/Local Bus + - NAND flash: 1GB 8-bit NAND flash + - NOR: 128MB 16-bit NOR Flash + - Ethernet + - Two on-board RGMII 10/100/1G ethernet ports. + - CPLD + - Clocks + - System and DDR clock (SYSCLK, “DDRCLK”) + - SERDES clocks + - Power Supplies + - USB + - Supports two USB 2.0 ports with integrated PHYs + - Two type A ports with 5V@1.5A per port. + - SDHC + - SDHC/SDXC connector + - SPI + - On-board 64MB SPI flash + - Other IO + - Two Serial ports + - Four I2C ports + +T1042RDB_PI board Overview +------------------------- + - SERDES Connections, 8 lanes information: + 1, 2, 3, 4 : PCIe x4 slot + 5: mini PCIe connector + 6: mini PCIe connector + 7: NA + 8: SATA connector + - DDR Controller + - Supports rates of up to 1600 MHz data-rate + - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types. + - IFC/Local Bus + - NAND flash: 1GB 8-bit NAND flash + - NOR: 128MB 16-bit NOR Flash + - Ethernet + - Two on-board RGMII 10/100/1G ethernet ports. + - CPLD + - Clocks + - System and DDR clock (SYSCLK, “DDRCLK”) + - SERDES clocks + - Video + - DIU supports video at up to 1280x1024x32bpp + - Power Supplies + - USB + - Supports two USB 2.0 ports with integrated PHYs + - Two type A ports with 5V@1.5A per port. + - SDHC + - SDHC/SDXC connector + - SPI + - On-board 64MB SPI flash + - Other IO + - Two Serial ports + - Four I2C ports + +Memory map +----------- +The addresses in brackets are physical addresses. + +Start Address End Address Description Size +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB +0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB +0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB +0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB +0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB +0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB +0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB +0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB +0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB +0xF_0000_0000 0xF_003F_FFFF DCSR 4MB +0xC_3000_0000 0xC_3FFF_FFFF PCI Express 4 Mem Space 256MB +0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB +0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB +0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB +0x0_0000_0000 0x0_ffff_ffff DDR 2GB + + +NOR Flash memory Map +--------------------- + Start End Definition Size +0xEFF40000 0xEFFFFFFF U-Boot (current bank) 768KB +0xEFF20000 0xEFF3FFFF U-Boot env (current bank) 128KB +0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB +0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB +0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB +0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB +0xEC000000 0xEC01FFFF RCW (alt bank) 128KB +0xEBF40000 0xEBFFFFFF U-Boot (alt bank) 768KB +0xEBF20000 0xEBF3FFFF U-Boot env (alt bank) 128KB +0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB +0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB +0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB +0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB +0xE8000000 0xE801FFFF RCW (current bank) 128KB + + +Various Software configurations/environment variables/commands +-------------------------------------------------------------- +The below commands apply to the board + +1. U-Boot environment variable hwconfig + The default hwconfig is: + hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1: + dr_mode=host,phy_type=utmi + Note: For USB gadget set "dr_mode=peripheral" + +2. FMAN Ucode versions + fsl_fman_ucode_t1040.bin + +3. Switching to alternate bank + Commands for switching to alternate bank. + + 1. To change from vbank0 to vbank4 + => cpld reset altbank (it will boot using vbank4) + + 2.To change from vbank4 to vbank0 + => cpld reset (it will boot using vbank0) + +NAND boot with 2 Stage boot loader +---------------------------------- +PBL initialise the internal SRAM and copy SPL(160KB) in SRAM. +SPL further initialise DDR using SPD and environment variables and copy +U-Boot(768 KB) from flash to DDR. +Finally SPL transer control to U-Boot for futher booting. + +SPL has following features: + - Executes within 256K + - No relocation required + + Run time view of SPL framework during boot :- + ----------------------------------------------- + Area | Address | +----------------------------------------------- + Secure boot | 0xFFFC0000 (32KB) | + headers | | + ----------------------------------------------- + GD, BD | 0xFFFC8000 (4KB) | + ----------------------------------------------- + ENV | 0xFFFC9000 (8KB) | + ----------------------------------------------- + HEAP | 0xFFFCB000 (30KB) | + ----------------------------------------------- + STACK | 0xFFFD8000 (22KB) | + ----------------------------------------------- + U-Boot SPL | 0xFFFD8000 (160KB) | + ----------------------------------------------- + +NAND Flash memory Map on T104xRDB +------------------------------------------ + Start End Definition Size +0x000000 0x0FFFFF U-Boot 1MB +0x180000 0x19FFFF U-Boot env 128KB +0x280000 0x29FFFF FMAN Ucode 128KB +0x380000 0x39FFFF QE Firmware 128KB + +SD Card memory Map on T104xRDB +------------------------------------------ + Block #blocks Definition Size +0x008 2048 U-Boot 1MB +0x800 0024 U-Boot env 8KB +0x820 0256 FMAN Ucode 128KB +0x920 0256 QE Firmware 128KB + +SPI Flash memory Map on T104xRDB +------------------------------------------ + Start End Definition Size +0x000000 0x0FFFFF U-Boot 1MB +0x100000 0x101FFF U-Boot env 8KB +0x110000 0x12FFFF FMAN Ucode 128KB +0x130000 0x14FFFF QE Firmware 128KB + +Please note QE Firmware is only valid for T1040RDB + + +Switch Settings for T104xRDB boards: (ON is 0, OFF is 1) +========================================================== +NOR boot SW setting: +SW1: 00010011 +SW2: 10111011 +SW3: 11100001 + +NAND boot SW setting: +SW1: 10001000 +SW2: 00111011 +SW3: 11110001 + +SPI boot SW setting: +SW1: 00100010 +SW2: 10111011 +SW3: 11100001 + +SD boot SW setting: +SW1: 00100000 +SW2: 00111011 +SW3: 11100001 + +Switch Settings for T104xD4RDB boards: (ON is 0, OFF is 1) +============================================================= +NOR boot SW setting: +SW1: 00010011 +SW2: 10111001 +SW3: 11100001 + +NAND boot SW setting: +SW1: 10001000 +SW2: 00111001 +SW3: 11110001 + +SPI boot SW setting: +SW1: 00100010 +SW2: 10111001 +SW3: 11100001 + +SD boot SW setting: +SW1: 00100000 +SW2: 00111001 +SW3: 11100001 + +PBL-based image generation +========================== +Changes only the required register bit in in PBI commands. + +Provides reference code which might needs some +modification as per requirement. +example: +By default PBI_SRC=14 (which is for IFC-NAND/NOR) in rcw.cfg file +which needs to be changed for SPI and SD. + +For SD-boot +============== +1. Set RCW[192:195], PBI_SRC bits as 6 in RCW file (t1040d4_rcw.cfg type files) + +example: + RCW file: board/freescale/t104xrdb/t1040d4_rcw.cfg + +Change +66000002 40000002 ec027000 01000000 +to +66000002 40000002 6c027000 01000000 + +2. SD does not support flush so remove flush from pbl, make changes in + tools/pblimage.c file, Update value of pbl_end_cmd[0] = 0x09138000 + with 0x091380c0 + +For SPI-boot +============== +1. Set RCW[192:195], PBI_SRC bits as 5 in RCW file (t1040d4_rcw.cfg type files) + +example: + RCW file: board/freescale/t104xrdb/t1040d4_rcw.cfg + +Change +66000002 40000002 ec027000 01000000 +to +66000002 40000002 5c027000 01000000 + +2. SPI does not support flush so remove flush from pbl, make changes in + tools/pblimage.c file, Update value of pbl_end_cmd[0] = 0x09138000 + with 0x091380c0 + +Device tree support and how to enable it for different configs +-------------------------------------------------------------- +Device tree support is available for t1042d4rdb for below mentioned boot, +1. NOR Boot +2. NAND Boot +3. SD Boot +4. SPIFLASH Boot + +To enable device tree support for other boot, below configs need to be +enabled in relative defconfig file, +1. CONFIG_DEFAULT_DEVICE_TREE="t1042d4rdb" (Change default device tree name if required) +2. CONFIG_OF_CONTROL +3. CONFIG_MPC85XX_HAVE_RESET_VECTOR if reset vector is located at + CONFIG_RESET_VECTOR_ADDRESS - 0xffc + +If device tree support is enabled in defconfig, +1. use 'u-boot-with-dtb.bin' for NOR boot. +2. use 'u-boot-with-spl-pbl.bin' for other boot. |