diff options
Diffstat (limited to 'roms/u-boot/board/hisilicon/hikey/README')
| -rw-r--r-- | roms/u-boot/board/hisilicon/hikey/README | 227 |
1 files changed, 227 insertions, 0 deletions
diff --git a/roms/u-boot/board/hisilicon/hikey/README b/roms/u-boot/board/hisilicon/hikey/README new file mode 100644 index 000000000..94e8397e9 --- /dev/null +++ b/roms/u-boot/board/hisilicon/hikey/README @@ -0,0 +1,227 @@ +Introduction +============ + +HiKey is the first certified 96Boards Consumer Edition board. The board/SoC has: - +* HiSilicon Kirin 6220 eight-core ARM Cortex-A53 64-bit SoC running at 1.2GHz. +* ARM Mali 450-MP4 GPU +* 1GB 800MHz LPDDR3 DRAM +* 4GB eMMC Flash Storage +* microSD +* 802.11a/b/g/n WiFi, Bluetooth + +The HiKey schematic can be found here: - +https://github.com/96boards/documentation/blob/master/consumer/hikey/hikey620/hardware-docs/HiKey_schematics_LeMaker_version_Rev_A1.pdf + +The SoC datasheet can be found here: - +https://github.com/96boards/documentation/blob/master/consumer/hikey/hikey620/hardware-docs/Hi6220V100_Multi-Mode_Application_Processor_Function_Description.pdf + +Currently the u-boot port supports: - +* USB +* eMMC +* SD card +* GPIO + +The HiKey U-Boot port has been tested with l-loader, booting ATF, which then boots +U-Boot as the bl33.bin executable. + +Compile from source +=================== + +First get all the sources + + > mkdir -p ~/hikey/src ~/hikey/bin + > cd ~/hikey/src + > git clone https://github.com/96boards-hikey/edk2 -b testing/hikey960_v2.5 + > git clone https://github.com/ARM-software/arm-trusted-firmware + > git clone https://github.com/96boards-hikey/l-loader -b testing/hikey960_v1.2 + > git clone https://github.com/96boards-hikey/OpenPlatformPkg -b testing/hikey960_v1.3.4 + > git clone https://github.com/96boards-hikey/atf-fastboot + > wget https://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey/release/hisi-idt.py + +Get the BL30 mcuimage.bin binary. It is shipped as part of the UEFI source. +The latest version can be obtained from the OpenPlatformPkg repo. + + > cp OpenPlatformPkg/Platforms/Hisilicon/HiKey/Binary/mcuimage.bin ~/hikey/bin/ + +Get nvme.img binary + > wget -P ~/hikey/bin https://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey/release/nvme.img + +Compile U-Boot +============== + + > cd ~/hikey/src/u-boot + > make CROSS_COMPILE=aarch64-linux-gnu- hikey_config + > make CROSS_COMPILE=aarch64-linux-gnu- + > cp u-boot.bin ~/hikey/bin + +Compile ARM Trusted Firmware (ATF) +================================== + + > cd ~/hikey/src/arm-trusted-firmware + > make CROSS_COMPILE=aarch64-linux-gnu- all fip \ + SCP_BL2=~/hikey/bin/mcuimage.bin \ + BL33=~/hikey/bin/u-boot.bin DEBUG=1 PLAT=hikey + +Copy the resulting FIP binary + > cp build/hikey/debug/fip.bin ~/hikey/bin + +Compile ATF Fastboot +==================== + + > cd ~/hikey/src/atf-fastboot + > make CROSS_COMPILE=aarch64-linux-gnu- PLAT=hikey DEBUG=1 + +Compile l-loader +================ + > cd ~/hikey/src/l-loader + > ln -sf ~/hikey/src/arm-trusted-firmware/build/hikey/debug/bl1.bin + > ln -sf ~/hikey/src/arm-trusted-firmware/build/hikey/debug/bl2.bin + > ln -sf ~/hikey/src/atf-fastboot/build/hikey/debug/bl1.bin fastboot.bin + > make hikey PTABLE_LST=aosp-8g + +Copy the resulting binaries + > cp *.img ~/hikey/bin + > cp l-loader.bin ~/hikey/bin + > cp recovery.bin ~/hikey/bin + +These instructions are adapted from +https://github.com/ARM-software/arm-trusted-firmware/blob/master/docs/plat/hikey.rst + +FLASHING +======== + +1. Connect the second jumper on J15 BOOT SEL, to go into recovery mode and flash l-loader.bin with +the hisi-idt.py utility. Then connect a USB A to B mini cable from your PC to the USB OTG port of HiKey and execute the below command. + +The command below assumes HiKey enumerated as the first USB serial port + + > sudo python ~/hikey/src/hisi-idt.py -d /dev/ttyUSB0 --img1 ~/hikey/bin/recovery.bin + +2. Once LED 0 comes on solid, HiKey board should be detected as a fastboot device. + + > sudo fastboot devices + +0123456789ABCDEF fastboot + +3. Flash the images + + > sudo fastboot flash ptable ~/hikey/bin/prm_ptable.img + > sudo fastboot flash loader ~/hikey/bin/l-loader.bin + > sudo fastboot flash fastboot ~/hikey/bin/fip.bin + > sudo fastboot flash nvme ~/hikey/bin/nvme.img + +4. Disconnect second jumper on J15 BOOT SEL, and reset the board and you will now (hopefully) + have ATF, booting u-boot from eMMC. + + Note: To get USB host working, also disconnect the USB OTG cable used for flashing. Otherwise you + will get 'dwc_otg_core_host_init: Timeout!' errors. + +See working boot trace below on UART3 available at Low Speed Expansion header: - + +NOTICE: BL2: v1.5(debug):v1.5-694-g6d4f6aea +NOTICE: BL2: Built : 09:21:42, Aug 29 2018 +INFO: BL2: Doing platform setup +INFO: ddr3 rank1 init pass +INFO: succeed to set ddrc 150mhz +INFO: ddr3 rank1 init pass +INFO: succeed to set ddrc 266mhz +INFO: ddr3 rank1 init pass +INFO: succeed to set ddrc 400mhz +INFO: ddr3 rank1 init pass +INFO: succeed to set ddrc 533mhz +INFO: ddr3 rank1 init pass +INFO: succeed to set ddrc 800mhz +INFO: Samsung DDR +INFO: ddr test value:0xa5a55a5a +INFO: BL2: TrustZone: protecting 16777216 bytes of memory at 0x3f000000 +INFO: BL2: TrustZone: protecting 4194304 bytes of memory at 0x3e800000 +INFO: [BDID] [fff91c18] midr: 0x410fd033 +INFO: init_acpu_dvfs: pmic version 17 +INFO: init_acpu_dvfs: ACPU_CHIP_MAX_FREQ=0x186a00. +INFO: acpu_dvfs_volt_init: success! +INFO: acpu_dvfs_set_freq: support freq num is 5 +INFO: acpu_dvfs_set_freq: start prof is 0x4 +INFO: acpu_dvfs_set_freq: magic is 0x5a5ac5c5 +INFO: acpu_dvfs_set_freq: voltage: +INFO: - 0: 0x49 +INFO: - 1: 0x49 +INFO: - 2: 0x50 +INFO: - 3: 0x60 +INFO: - 4: 0x78 +NOTICE: acpu_dvfs_set_freq: set acpu freq success!INFO: BL2: Loading image id 2 +INFO: Loading image id=2 at address 0x1000000 +INFO: Image id=2 loaded: 0x1000000 - 0x1023d00 +INFO: hisi_mcu_load_image: mcu sections 0: +INFO: hisi_mcu_load_image: src = 0x1000200 +INFO: hisi_mcu_load_image: dst = 0xf6000000 +INFO: hisi_mcu_load_image: size = 31184 +INFO: hisi_mcu_load_image: [SRC 0x1000200] 0x8000 0x3701 0x7695 0x7689 +INFO: hisi_mcu_load_image: [DST 0xf6000000] 0x8000 0x3701 0x7695 0x7689 +INFO: hisi_mcu_load_image: mcu sections 1: +INFO: hisi_mcu_load_image: src = 0x1007bd0 +INFO: hisi_mcu_load_image: dst = 0x5e00000 +INFO: hisi_mcu_load_image: size = 93828 +INFO: hisi_mcu_load_image: [SRC 0x1007bd0] 0xf000b510 0x2103fb3d 0xf0004604 0xf003fb57 +INFO: hisi_mcu_load_image: [DST 0x5e00000] 0xf000b510 0x2103fb3d 0xf0004604 0xf003fb57 +INFO: hisi_mcu_load_image: mcu sections 2: +INFO: hisi_mcu_load_image: src = 0x101ea54 +INFO: hisi_mcu_load_image: dst = 0x5e16e84 +INFO: hisi_mcu_load_image: size = 15428 +INFO: hisi_mcu_load_image: [SRC 0x101ea54] 0x9 0x1020640 0x10001 0x8f0d180 +INFO: hisi_mcu_load_image: [DST 0x5e16e84] 0x9 0x1020640 0x10001 0x8f0d180 +INFO: hisi_mcu_load_image: mcu sections 3: +INFO: hisi_mcu_load_image: src = 0x1022698 +INFO: hisi_mcu_load_image: dst = 0x5e22a10 +INFO: hisi_mcu_load_image: size = 3060 +INFO: hisi_mcu_load_image: [SRC 0x1022698] 0x0 0x0 0x0 0x0 +INFO: hisi_mcu_load_image: [DST 0x5e22a10] 0x0 0x0 0x0 0x0 +INFO: hisi_mcu_load_image: mcu sections 4: +INFO: hisi_mcu_load_image: src = 0x102328c +INFO: hisi_mcu_load_image: dst = 0x5e23604 +INFO: hisi_mcu_load_image: size = 2616 +INFO: hisi_mcu_load_image: [SRC 0x102328c] 0xf80000a0 0x0 0xf80000ac 0x0 +INFO: hisi_mcu_load_image: [DST 0x5e23604] 0xf80000a0 0x0 0xf80000ac 0x0 +INFO: hisi_mcu_start_run: AO_SC_SYS_CTRL2=0 +INFO: plat_hikey_bl2_handle_scp_bl2: MCU PC is at 0x42933301 +INFO: plat_hikey_bl2_handle_scp_bl2: AO_SC_PERIPH_CLKSTAT4 is 0x3b018f09 +WARNING: BL2: Platform setup already done!! +INFO: BL2: Loading image id 3 +INFO: Loading image id=3 at address 0xf9858000 +INFO: Image id=3 loaded: 0xf9858000 - 0xf9860058 +INFO: BL2: Loading image id 5 +INFO: Loading image id=5 at address 0x35000000 +INFO: Image id=5 loaded: 0x35000000 - 0x35061cd2 +NOTICE: BL2: Booting BL31 +INFO: Entry point address = 0xf9858000 +INFO: SPSR = 0x3cd +NOTICE: BL31: v1.5(debug):v1.5-694-g6d4f6aea +NOTICE: BL31: Built : 09:21:44, Aug 29 2018 +WARNING: Using deprecated integer interrupt array in gicv2_driver_data_t +WARNING: Please migrate to using an interrupt_prop_t array +INFO: ARM GICv2 driver initialized +INFO: BL31: Initializing runtime services +INFO: BL31: cortex_a53: CPU workaround for disable_non_temporal_hint was applied +INFO: BL31: cortex_a53: CPU workaround for 843419 was applied +INFO: BL31: cortex_a53: CPU workaround for 855873 was applied +INFO: BL31: Preparing for EL3 exit to normal world +INFO: Entry point address = 0x35000000 +INFO: SPSR = 0x3c9 + + +U-Boot 2018.09-rc1 (Aug 22 2018 - 14:55:49 +0530)hikey + +DRAM: 990 MiB +HI6553 PMIC init +MMC: config_sd_carddetect: SD card present +Hisilicon DWMMC: 0, Hisilicon DWMMC: 1 +Loading Environment from FAT... Unable to use mmc 1:1... Failed (-5) +In: uart@f7113000 +Out: uart@f7113000 +Err: uart@f7113000 +Net: Net Initialization Skipped +No ethernet found. +Hit any key to stop autoboot: 0 +starting USB... +USB0: scanning bus 0 for devices... 2 USB Device(s) found + scanning usb for storage devices... 0 Storage Device(s) found + scanning usb for ethernet devices... 0 Ethernet Device(s) found |