diff options
Diffstat (limited to 'roms/u-boot/board/keymile/km_arm')
| -rw-r--r-- | roms/u-boot/board/keymile/km_arm/Kconfig | 69 | ||||
| -rw-r--r-- | roms/u-boot/board/keymile/km_arm/MAINTAINERS | 11 | ||||
| -rw-r--r-- | roms/u-boot/board/keymile/km_arm/Makefile | 11 | ||||
| -rw-r--r-- | roms/u-boot/board/keymile/km_arm/fpga_config.c | 255 | ||||
| -rw-r--r-- | roms/u-boot/board/keymile/km_arm/km_arm.c | 520 | ||||
| -rw-r--r-- | roms/u-boot/board/keymile/km_arm/kwbimage-memphis.cfg | 179 | ||||
| -rw-r--r-- | roms/u-boot/board/keymile/km_arm/kwbimage.cfg | 161 | ||||
| -rw-r--r-- | roms/u-boot/board/keymile/km_arm/kwbimage_128M16_1.cfg | 257 | ||||
| -rw-r--r-- | roms/u-boot/board/keymile/km_arm/kwbimage_256M8_1.cfg | 257 |
9 files changed, 1720 insertions, 0 deletions
diff --git a/roms/u-boot/board/keymile/km_arm/Kconfig b/roms/u-boot/board/keymile/km_arm/Kconfig new file mode 100644 index 000000000..6f55cfab8 --- /dev/null +++ b/roms/u-boot/board/keymile/km_arm/Kconfig @@ -0,0 +1,69 @@ +menu "KM ARM Options" + depends on ARM + +config KM_FPGA_CONFIG + bool "FPGA Configuration" + default n + help + Include capability to change FPGA configuration. + +config KM_FPGA_FORCE_CONFIG + bool "FPGA reconfiguration" + default n + help + If yes we force to reconfigure the FPGA always + +config KM_FPGA_NO_RESET + bool "FPGA skip reset" + default n + help + If yes we skip triggering a reset of the FPGA + +config KM_ENV_IS_IN_SPI_NOR + bool "Environment in SPI NOR" + default n + help + Put the U-Boot environment in the SPI NOR flash. + +config KM_PIGGY4_88E6061 + bool "Piggy via Switch 88E6061" + default n + help + The Piggy4 board is connected via a Marvell 88E6061 switch. + +config KM_PIGGY4_88E6352 + bool "Piggy via Switch 88E6352" + default n + help + The Piggy4 board is connected via a Marvell 88E6352 switch. + +endmenu + +if TARGET_KM_KIRKWOOD + +config SYS_BOARD + default "km_arm" + +config SYS_VENDOR + default "keymile" + +config SYS_CONFIG_NAME + default "km_kirkwood" + +config BOARD_SPECIFIC_OPTIONS # dummy + def_bool y + select BOARD_LATE_INIT + select DM + select DM_ETH + select DM_SERIAL + select DM_SPI + select DM_SPI_FLASH + select USB + select USB_EHCI_HCD + select USB_EHCI_MARVELL + imply CMD_CRAMFS + imply CMD_DIAG + imply FS_CRAMFS + imply CMD_USB + +endif diff --git a/roms/u-boot/board/keymile/km_arm/MAINTAINERS b/roms/u-boot/board/keymile/km_arm/MAINTAINERS new file mode 100644 index 000000000..8da58da96 --- /dev/null +++ b/roms/u-boot/board/keymile/km_arm/MAINTAINERS @@ -0,0 +1,11 @@ +KM_ARM BOARD +M: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com> +S: Maintained +F: board/keymile/km_arm/ +F: include/configs/km_kirkwood.h +F: configs/km_kirkwood_defconfig +F: configs/km_kirkwood_128m16_defconfig +F: configs/km_kirkwood_pci_defconfig +F: configs/kmcoge5un_defconfig +F: configs/kmnusa_defconfig +F: configs/kmsuse2_defconfig diff --git a/roms/u-boot/board/keymile/km_arm/Makefile b/roms/u-boot/board/keymile/km_arm/Makefile new file mode 100644 index 000000000..79ccc763e --- /dev/null +++ b/roms/u-boot/board/keymile/km_arm/Makefile @@ -0,0 +1,11 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Prafulla Wadaskar <prafulla@marvell.com> + +obj-y := km_arm.o ../common/common.o ../common/ivm.o + +ifdef CONFIG_KM_FPGA_CONFIG +obj-y += fpga_config.o +endif diff --git a/roms/u-boot/board/keymile/km_arm/fpga_config.c b/roms/u-boot/board/keymile/km_arm/fpga_config.c new file mode 100644 index 000000000..839b162ee --- /dev/null +++ b/roms/u-boot/board/keymile/km_arm/fpga_config.c @@ -0,0 +1,255 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2012 + * Valentin Lontgchamp, Keymile AG, valentin.longchamp@keymile.com + */ + +#include <common.h> +#include <i2c.h> +#include <linux/delay.h> +#include <linux/errno.h> + +/* GPIO Pin from kirkwood connected to PROGRAM_B pin of the xilinx FPGA */ +#define KM_XLX_PROGRAM_B_PIN 39 + +#define BOCO_ADDR 0x10 + +#define ID_REG 0x00 +#define BOCO2_ID 0x5b + +static int check_boco2(void) +{ + int ret; + u8 id; + + ret = i2c_read(BOCO_ADDR, ID_REG, 1, &id, 1); + if (ret) { + printf("%s: error reading the BOCO id !!\n", __func__); + return ret; + } + + return (id == BOCO2_ID); +} + +static int boco_clear_bits(u8 reg, u8 flags) +{ + int ret; + u8 regval; + + /* give access to the EEPROM from FPGA */ + ret = i2c_read(BOCO_ADDR, reg, 1, ®val, 1); + if (ret) { + printf("%s: error reading the BOCO @%#x !!\n", + __func__, reg); + return ret; + } + regval &= ~flags; + ret = i2c_write(BOCO_ADDR, reg, 1, ®val, 1); + if (ret) { + printf("%s: error writing the BOCO @%#x !!\n", + __func__, reg); + return ret; + } + + return 0; +} + +static int boco_set_bits(u8 reg, u8 flags) +{ + int ret; + u8 regval; + + /* give access to the EEPROM from FPGA */ + ret = i2c_read(BOCO_ADDR, reg, 1, ®val, 1); + if (ret) { + printf("%s: error reading the BOCO @%#x !!\n", + __func__, reg); + return ret; + } + regval |= flags; + ret = i2c_write(BOCO_ADDR, reg, 1, ®val, 1); + if (ret) { + printf("%s: error writing the BOCO @%#x !!\n", + __func__, reg); + return ret; + } + + return 0; +} + +#define SPI_REG 0x06 +#define CFG_EEPROM 0x02 +#define FPGA_PROG 0x04 +#define FPGA_INIT_B 0x10 +#define FPGA_DONE 0x20 + +#ifndef CONFIG_KM_FPGA_FORCE_CONFIG +static int fpga_done(void) +{ + int ret = 0; + u8 regval; + + /* this is only supported with the boco2 design */ + if (!check_boco2()) + return 0; + + ret = i2c_read(BOCO_ADDR, SPI_REG, 1, ®val, 1); + if (ret) { + printf("%s: error reading the BOCO @%#x !!\n", + __func__, SPI_REG); + return 0; + } + + return regval & FPGA_DONE ? 1 : 0; +} +#endif /* CONFIG_KM_FPGA_FORCE_CONFIG */ + +static int skip; + +int trigger_fpga_config(void) +{ + int ret = 0; + + skip = 0; +#ifndef CONFIG_KM_FPGA_FORCE_CONFIG + /* if the FPGA is already configured, we do not want to + * reconfigure it + */ + skip = 0; + if (fpga_done()) { + printf("PCIe FPGA config: skipped\n"); + skip = 1; + return 0; + } +#endif /* CONFIG_KM_FPGA_FORCE_CONFIG */ + + if (check_boco2()) { + /* we have a BOCO2, this has to be triggered here */ + + /* make sure the FPGA_can access the EEPROM */ + ret = boco_clear_bits(SPI_REG, CFG_EEPROM); + if (ret) + return ret; + + /* trigger the config start */ + ret = boco_clear_bits(SPI_REG, FPGA_PROG | FPGA_INIT_B); + if (ret) + return ret; + + /* small delay for the pulse */ + udelay(10); + + /* up signal for pulse end */ + ret = boco_set_bits(SPI_REG, FPGA_PROG); + if (ret) + return ret; + + /* finally, raise INIT_B to remove the config delay */ + ret = boco_set_bits(SPI_REG, FPGA_INIT_B); + if (ret) + return ret; + + } else { + /* we do it the old way, with the gpio pin */ + kw_gpio_set_valid(KM_XLX_PROGRAM_B_PIN, 1); + kw_gpio_direction_output(KM_XLX_PROGRAM_B_PIN, 0); + /* small delay for the pulse */ + udelay(10); + kw_gpio_direction_input(KM_XLX_PROGRAM_B_PIN); + } + + return 0; +} + +int wait_for_fpga_config(void) +{ + int ret = 0; + u8 spictrl; + u32 timeout = 20000; + + if (skip) + return 0; + + if (!check_boco2()) { + /* we do not have BOCO2, this is not really used */ + return 0; + } + + printf("PCIe FPGA config:"); + do { + ret = i2c_read(BOCO_ADDR, SPI_REG, 1, &spictrl, 1); + if (ret) { + printf("%s: error reading the BOCO spictrl !!\n", + __func__); + return ret; + } + if (timeout-- == 0) { + printf(" FPGA_DONE timeout\n"); + return -EFAULT; + } + udelay(10); + } while (!(spictrl & FPGA_DONE)); + + printf(" done\n"); + + return 0; +} + +#if defined(CONFIG_KM_FPGA_NO_RESET) +int fpga_reset(void) +{ + /* no dedicated reset pin for FPGA */ + return 0; +} +#else + +#define PRST1 0x4 +#define PCIE_RST 0x10 +#define TRAFFIC_RST 0x04 + +int fpga_reset(void) +{ + int ret = 0; + u8 resets; + + if (!check_boco2()) { + /* we do not have BOCO2, this is not really used */ + return 0; + } + + /* if we have skipped, we only want to reset the PCIe part */ + resets = skip ? PCIE_RST : PCIE_RST | TRAFFIC_RST; + + ret = boco_clear_bits(PRST1, resets); + if (ret) + return ret; + + /* small delay for the pulse */ + udelay(10); + + ret = boco_set_bits(PRST1, resets); + if (ret) + return ret; + + return 0; +} +#endif + +/* the FPGA was configured, we configure the BOCO2 so that the EEPROM + * is available from the Bobcat SPI bus + */ +int toggle_eeprom_spi_bus(void) +{ + int ret = 0; + + if (!check_boco2()) { + /* we do not have BOCO2, this is not really used */ + return 0; + } + + ret = boco_set_bits(SPI_REG, CFG_EEPROM); + if (ret) + return ret; + + return 0; +} diff --git a/roms/u-boot/board/keymile/km_arm/km_arm.c b/roms/u-boot/board/keymile/km_arm/km_arm.c new file mode 100644 index 000000000..e9af090a3 --- /dev/null +++ b/roms/u-boot/board/keymile/km_arm/km_arm.c @@ -0,0 +1,520 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla@marvell.com> + * + * (C) Copyright 2009 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * (C) Copyright 2010 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + */ + +#include <common.h> +#include <env.h> +#include <i2c.h> +#include <init.h> +#include <nand.h> +#include <net.h> +#include <netdev.h> +#include <miiphy.h> +#include <spi.h> +#include <asm/global_data.h> +#include <asm/io.h> +#include <asm/arch/cpu.h> +#include <asm/arch/soc.h> +#include <asm/arch/mpp.h> + +#include "../common/common.h" + +DECLARE_GLOBAL_DATA_PTR; + +/* + * BOCO FPGA definitions + */ +#define BOCO 0x10 +#define REG_CTRL_H 0x02 +#define MASK_WRL_UNITRUN 0x01 +#define MASK_RBX_PGY_PRESENT 0x40 +#define REG_IRQ_CIRQ2 0x2d +#define MASK_RBI_DEFECT_16 0x01 + +/* + * PHY registers definitions + */ +#define PHY_MARVELL_OUI 0x5043 +#define PHY_MARVELL_88E1118_MODEL 0x0022 +#define PHY_MARVELL_88E1118R_MODEL 0x0024 + +#define PHY_MARVELL_PAGE_REG 0x0016 +#define PHY_MARVELL_DEFAULT_PAGE 0x0000 + +#define PHY_MARVELL_88E1118R_LED_CTRL_PAGE 0x0003 +#define PHY_MARVELL_88E1118R_LED_CTRL_REG 0x0010 + +#define PHY_MARVELL_88E1118R_LED_CTRL_RESERVED 0x1000 +#define PHY_MARVELL_88E1118R_LED_CTRL_LED0_1000MB (0x7 << 0) +#define PHY_MARVELL_88E1118R_LED_CTRL_LED1_ACT (0x3 << 4) +#define PHY_MARVELL_88E1118R_LED_CTRL_LED2_LINK (0x0 << 8) + +/* I/O pin to erase flash RGPP09 = MPP43 */ +#define KM_FLASH_ERASE_ENABLE 43 + +/* Multi-Purpose Pins Functionality configuration */ +static const u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_PEX_RST_OUTn, +#if defined(CONFIG_SYS_I2C_SOFT) + MPP8_GPIO, /* SDA */ + MPP9_GPIO, /* SCL */ +#endif + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_GPO, /* Reserved */ + MPP13_UART1_TXD, + MPP14_UART1_RXD, + MPP15_GPIO, /* Not used */ + MPP16_GPIO, /* Not used */ + MPP17_GPIO, /* Reserved */ + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GPIO, + MPP21_GPIO, + MPP22_GPIO, + MPP23_GPIO, + MPP24_GPIO, + MPP25_GPIO, + MPP26_GPIO, + MPP27_GPIO, + MPP28_GPIO, + MPP29_GPIO, + MPP30_GPIO, + MPP31_GPIO, + MPP32_GPIO, + MPP33_GPIO, + MPP34_GPIO, /* CDL1 (input) */ + MPP35_GPIO, /* CDL2 (input) */ + MPP36_GPIO, /* MAIN_IRQ (input) */ + MPP37_GPIO, /* BOARD_LED */ + MPP38_GPIO, /* Piggy3 LED[1] */ + MPP39_GPIO, /* Piggy3 LED[2] */ + MPP40_GPIO, /* Piggy3 LED[3] */ + MPP41_GPIO, /* Piggy3 LED[4] */ + MPP42_GPIO, /* Piggy3 LED[5] */ + MPP43_GPIO, /* Piggy3 LED[6] */ + MPP44_GPIO, /* Piggy3 LED[7], BIST_EN_L */ + MPP45_GPIO, /* Piggy3 LED[8] */ + MPP46_GPIO, /* Reserved */ + MPP47_GPIO, /* Reserved */ + MPP48_GPIO, /* Reserved */ + MPP49_GPIO, /* SW_INTOUTn */ + 0 +}; + +static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN]; + +#if (defined(CONFIG_KM_PIGGY4_88E6061)|defined(CONFIG_KM_PIGGY4_88E6352)) +/* + * All boards with PIGGY4 connected via a simple switch have ethernet always + * present. + */ +int ethernet_present(void) +{ + return 1; +} +#else +int ethernet_present(void) +{ + uchar buf; + int ret = 0; + + if (i2c_read(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) { + printf("%s: Error reading Boco\n", __func__); + return -1; + } + if ((buf & MASK_RBX_PGY_PRESENT) == MASK_RBX_PGY_PRESENT) + ret = 1; + + return ret; +} +#endif + +static int initialize_unit_leds(void) +{ + /* + * Init the unit LEDs per default they all are + * ok apart from bootstat + */ + uchar buf; + + if (i2c_read(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) { + printf("%s: Error reading Boco\n", __func__); + return -1; + } + buf |= MASK_WRL_UNITRUN; + if (i2c_write(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) { + printf("%s: Error writing Boco\n", __func__); + return -1; + } + return 0; +} + +static void set_bootcount_addr(void) +{ + uchar buf[32]; + unsigned int bootcountaddr; + + bootcountaddr = gd->ram_size - BOOTCOUNT_ADDR; + sprintf((char *)buf, "0x%x", bootcountaddr); + env_set("bootcountaddr", (char *)buf); +} + +int misc_init_r(void) +{ + ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN, + CONFIG_PIGGY_MAC_ADDRESS_OFFSET); + + initialize_unit_leds(); + set_km_env(); + set_bootcount_addr(); + return 0; +} + +int board_early_init_f(void) +{ +#if defined(CONFIG_SYS_I2C_SOFT) + u32 tmp; + + /* set the 2 bitbang i2c pins as output gpios */ + tmp = readl(MVEBU_GPIO0_BASE + 4); + writel(tmp & (~KM_KIRKWOOD_SOFT_I2C_GPIOS), MVEBU_GPIO0_BASE + 4); +#endif + /* adjust SDRAM size for bank 0 */ + mvebu_sdram_size_adjust(0); + kirkwood_mpp_conf(kwmpp_config, NULL); + return 0; +} + +int board_init(void) +{ + /* address of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + + /* + * The KM_FLASH_GPIO_PIN switches between using a + * NAND or a SPI FLASH. Set this pin on start + * to NAND mode. + */ + kw_gpio_set_valid(KM_FLASH_GPIO_PIN, 1); + kw_gpio_direction_output(KM_FLASH_GPIO_PIN, 1); + +#if defined(CONFIG_SYS_I2C_SOFT) + /* + * Reinit the GPIO for I2C Bitbang driver so that the now + * available gpio framework is consistent. The calls to + * direction output in are not necessary, they are already done in + * board_early_init_f + */ + kw_gpio_set_valid(KM_KIRKWOOD_SDA_PIN, 1); + kw_gpio_set_valid(KM_KIRKWOOD_SCL_PIN, 1); +#endif + +#if defined(CONFIG_SYS_EEPROM_WREN) + kw_gpio_set_valid(KM_KIRKWOOD_ENV_WP, 38); + kw_gpio_direction_output(KM_KIRKWOOD_ENV_WP, 1); +#endif + +#if defined(CONFIG_KM_FPGA_CONFIG) + trigger_fpga_config(); +#endif + + return 0; +} + +int board_late_init(void) +{ +#if defined(CONFIG_KM_COGE5UN) + u8 dip_switch = kw_gpio_get_value(KM_FLASH_ERASE_ENABLE); + + /* if pin 1 do full erase */ + if (dip_switch != 0) { + /* start bootloader */ + puts("DIP: Enabled\n"); + env_set("actual_bank", "0"); + } +#endif + +#if defined(CONFIG_KM_FPGA_CONFIG) + wait_for_fpga_config(); + fpga_reset(); + toggle_eeprom_spi_bus(); +#endif + return 0; +} + +static const u32 spi_mpp_config[] = { + MPP1_SPI_MOSI, + MPP2_SPI_SCK, + MPP3_SPI_MISO, + 0 +}; + +static u32 spi_mpp_backup[4]; + +int mvebu_board_spi_claim_bus(struct udevice *dev) +{ + spi_mpp_backup[3] = 0; + + /* set new spi mpp config and save current one */ + kirkwood_mpp_conf(spi_mpp_config, spi_mpp_backup); + + kw_gpio_set_value(KM_FLASH_GPIO_PIN, 0); + + return 0; +} + +int mvebu_board_spi_release_bus(struct udevice *dev) +{ + /* restore saved mpp config */ + kirkwood_mpp_conf(spi_mpp_backup, NULL); + + kw_gpio_set_value(KM_FLASH_GPIO_PIN, 1); + + return 0; +} + +#if (defined(CONFIG_KM_PIGGY4_88E6061)) + +#define PHY_LED_SEL_REG 0x18 +#define PHY_LED0_LINK (0x5) +#define PHY_LED1_ACT (0x8 << 4) +#define PHY_LED2_INT (0xe << 8) +#define PHY_SPEC_CTRL_REG 0x1c +#define PHY_RGMII_CLK_STABLE (0x1 << 10) +#define PHY_CLSA (0x1 << 1) + +/* Configure and enable MV88E3018 PHY */ +void reset_phy(void) +{ + char *name = "egiga0"; + unsigned short reg; + + if (miiphy_set_current_dev(name)) + return; + + /* RGMII clk transition on data stable */ + if (miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, ®)) + printf("Error reading PHY spec ctrl reg\n"); + if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, + reg | PHY_RGMII_CLK_STABLE | PHY_CLSA)) + printf("Error writing PHY spec ctrl reg\n"); + + /* leds setup */ + if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL_REG, + PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT)) + printf("Error writing PHY LED reg\n"); + + /* reset the phy */ + miiphy_reset(name, CONFIG_PHY_BASE_ADR); +} +#elif defined(CONFIG_KM_PIGGY4_88E6352) + +#include <mv88e6352.h> + +#if defined(CONFIG_KM_NUSA) +struct mv88e_sw_reg extsw_conf[] = { + /* + * port 0, PIGGY4, autoneg + * first the fix for the 1000Mbits Autoneg, this is from + * a Marvell errata, the regs are undocumented + */ + { PHY(0), PHY_PAGE, AN1000FIX_PAGE }, + { PHY(0), PHY_STATUS, AN1000FIX }, + { PHY(0), PHY_PAGE, 0 }, + /* now the real port and phy configuration */ + { PORT(0), PORT_PHY, NO_SPEED_FOR }, + { PORT(0), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, + { PHY(0), PHY_1000_CTRL, NO_ADV }, + { PHY(0), PHY_SPEC_CTRL, AUTO_MDIX_EN }, + { PHY(0), PHY_CTRL, PHY_100_MBPS | AUTONEG_EN | AUTONEG_RST | + FULL_DUPLEX }, + /* port 1, unused */ + { PORT(1), PORT_CTRL, PORT_DIS }, + { PHY(1), PHY_CTRL, PHY_PWR_DOWN }, + { PHY(1), PHY_SPEC_CTRL, SPEC_PWR_DOWN }, + /* port 2, unused */ + { PORT(2), PORT_CTRL, PORT_DIS }, + { PHY(2), PHY_CTRL, PHY_PWR_DOWN }, + { PHY(2), PHY_SPEC_CTRL, SPEC_PWR_DOWN }, + /* port 3, unused */ + { PORT(3), PORT_CTRL, PORT_DIS }, + { PHY(3), PHY_CTRL, PHY_PWR_DOWN }, + { PHY(3), PHY_SPEC_CTRL, SPEC_PWR_DOWN }, + /* port 4, ICNEV, SerDes, SGMII */ + { PORT(4), PORT_STATUS, NO_PHY_DETECT }, + { PORT(4), PORT_PHY, SPEED_1000_FOR }, + { PORT(4), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, + { PHY(4), PHY_CTRL, PHY_PWR_DOWN }, + { PHY(4), PHY_SPEC_CTRL, SPEC_PWR_DOWN }, + /* port 5, CPU_RGMII */ + { PORT(5), PORT_PHY, RX_RGMII_TIM | TX_RGMII_TIM | FLOW_CTRL_EN | + FLOW_CTRL_FOR | LINK_VAL | LINK_FOR | FULL_DPX | + FULL_DPX_FOR | SPEED_1000_FOR }, + { PORT(5), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, + /* port 6, unused, this port has no phy */ + { PORT(6), PORT_CTRL, PORT_DIS }, +}; +#else +struct mv88e_sw_reg extsw_conf[] = {}; +#endif + +void reset_phy(void) +{ +#if defined(CONFIG_KM_MVEXTSW_ADDR) + char *name = "egiga0"; + + if (miiphy_set_current_dev(name)) + return; + + mv88e_sw_program(name, CONFIG_KM_MVEXTSW_ADDR, extsw_conf, + ARRAY_SIZE(extsw_conf)); + mv88e_sw_reset(name, CONFIG_KM_MVEXTSW_ADDR); +#endif +} + +#else +/* Configure and enable MV88E1118 PHY on the piggy*/ +void reset_phy(void) +{ + unsigned int oui; + unsigned char model, rev; + + char *name = "egiga0"; + + if (miiphy_set_current_dev(name)) + return; + + /* reset the phy */ + miiphy_reset(name, CONFIG_PHY_BASE_ADR); + + /* get PHY model */ + if (miiphy_info(name, CONFIG_PHY_BASE_ADR, &oui, &model, &rev)) + return; + + /* check for Marvell 88E1118R Gigabit PHY (PIGGY3) */ + if (oui == PHY_MARVELL_OUI && + model == PHY_MARVELL_88E1118R_MODEL) { + /* set page register to 3 */ + if (miiphy_write(name, CONFIG_PHY_BASE_ADR, + PHY_MARVELL_PAGE_REG, + PHY_MARVELL_88E1118R_LED_CTRL_PAGE)) + printf("Error writing PHY page reg\n"); + + /* + * leds setup as printed on PCB: + * LED2 (Link): 0x0 (On Link, Off No Link) + * LED1 (Activity): 0x3 (On Activity, Off No Activity) + * LED0 (Speed): 0x7 (On 1000 MBits, Off Else) + */ + if (miiphy_write(name, CONFIG_PHY_BASE_ADR, + PHY_MARVELL_88E1118R_LED_CTRL_REG, + PHY_MARVELL_88E1118R_LED_CTRL_RESERVED | + PHY_MARVELL_88E1118R_LED_CTRL_LED0_1000MB | + PHY_MARVELL_88E1118R_LED_CTRL_LED1_ACT | + PHY_MARVELL_88E1118R_LED_CTRL_LED2_LINK)) + printf("Error writing PHY LED reg\n"); + + /* set page register back to 0 */ + if (miiphy_write(name, CONFIG_PHY_BASE_ADR, + PHY_MARVELL_PAGE_REG, + PHY_MARVELL_DEFAULT_PAGE)) + printf("Error writing PHY page reg\n"); + } +} +#endif + +#if defined(CONFIG_HUSH_INIT_VAR) +int hush_init_var(void) +{ + ivm_analyze_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN); + return 0; +} +#endif + +#if defined(CONFIG_SYS_I2C_SOFT) +void set_sda(int state) +{ + I2C_ACTIVE; + I2C_SDA(state); +} + +void set_scl(int state) +{ + I2C_SCL(state); +} + +int get_sda(void) +{ + I2C_TRISTATE; + return I2C_READ; +} + +int get_scl(void) +{ + return kw_gpio_get_value(KM_KIRKWOOD_SCL_PIN) ? 1 : 0; +} +#endif + +#if defined(CONFIG_POST) + +#define KM_POST_EN_L 44 +#define POST_WORD_OFF 8 + +int post_hotkeys_pressed(void) +{ + if (IS_ENABLED(CONFIG_KM_COGE5UN)) + return kw_gpio_get_value(KM_POST_EN_L); + else + return !kw_gpio_get_value(KM_POST_EN_L); +} + +ulong post_word_load(void) +{ + void *addr = (void *)(gd->ram_size - BOOTCOUNT_ADDR + POST_WORD_OFF); + + return in_le32(addr); + +} +void post_word_store(ulong value) +{ + void *addr = (void *)(gd->ram_size - BOOTCOUNT_ADDR + POST_WORD_OFF); + + out_le32(addr, value); +} + +int arch_memory_test_prepare(u32 *vstart, u32 *size, phys_addr_t *phys_offset) +{ + *vstart = CONFIG_SYS_SDRAM_BASE; + + /* we go up to relocation plus a 1 MB margin */ + *size = CONFIG_SYS_TEXT_BASE - (1 << 20); + + return 0; +} +#endif + +#if defined(CONFIG_SYS_EEPROM_WREN) +int eeprom_write_enable(unsigned int dev_addr, int state) +{ + kw_gpio_set_value(KM_KIRKWOOD_ENV_WP, !state); + + return !kw_gpio_get_value(KM_KIRKWOOD_ENV_WP); +} +#endif diff --git a/roms/u-boot/board/keymile/km_arm/kwbimage-memphis.cfg b/roms/u-boot/board/keymile/km_arm/kwbimage-memphis.cfg new file mode 100644 index 000000000..d850e1011 --- /dev/null +++ b/roms/u-boot/board/keymile/km_arm/kwbimage-memphis.cfg @@ -0,0 +1,179 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# (C) Copyright 2010 +# Heiko Schocher, DENX Software Engineering, hs@denx.de. +# +# (C) Copyright 2011 +# Valentin Longchamp, Keymile AG, valentin.longchamp@keymile.com +# Refer doc/README.kwbimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM spi # Boot from SPI flash + +DATA 0xFFD10000 0x01112222 # MPP Control 0 Register +# bit 3-0: MPPSel0 2, NF_IO[2] +# bit 7-4: MPPSel1 2, NF_IO[3] +# bit 12-8: MPPSel2 2, NF_IO[4] +# bit 15-12: MPPSel3 2, NF_IO[5] +# bit 19-16: MPPSel4 1, NF_IO[6] +# bit 23-20: MPPSel5 1, NF_IO[7] +# bit 27-24: MPPSel6 1, SYSRST_O +# bit 31-28: MPPSel7 0, GPO[7] + +DATA 0xFFD10004 0x03303300 + +DATA 0xFFD10008 0x00001100 # MPP Control 2 Register +# bit 3-0: MPPSel16 0, GPIO[16] +# bit 7-4: MPPSel17 0, GPIO[17] +# bit 12-8: MPPSel18 1, NF_IO[0] +# bit 15-12: MPPSel19 1, NF_IO[1] +# bit 19-16: MPPSel20 0, GPIO[20] +# bit 23-20: MPPSel21 0, GPIO[21] +# bit 27-24: MPPSel22 0, GPIO[22] +# bit 31-28: MPPSel23 0, GPIO[23] + +DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register +DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register +DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register + +# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched! +# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage + +#Dram initalization +DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register +# bit13-0: 0x4E0 (DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x38543000 # DDR Controller Control Low +# bit 3-0: 0 reserved +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 5=recommended value for CL=4 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 8= CL+4, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x2302433E # DDR Timing (Low) (active cycles value +1) +# bit3-0: TRAS lsbs +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000A3E # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x00000001 # DDR Address Control +# bit1-0: 01, Cs0width=x16 +# bit3-2: 00, Cs0size=2Gb +# bit5-4: 00, Cs2width=nonexistent +# bit7-6: 00, Cs1size =nonexistent +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000652 # DDR Mode +DATA 0xFFD01420 0x00000006 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 1, DDR drive strenght reduced +# bit2: 1, DDR ODT control lsd disabled +# bit5-3: 000, required +# bit6: 0, DDR ODT control msb disabled +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 0 +# bit8 : 1 , add a sample stage +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00084520 # DDR2 SDRAM Timing Low +# bit3-0 : 0000, required +# bit7-4 : 0010, M_ODT assertion 2 cycles after read +# bit11-8 : 0101, M_ODT de-assertion 5 cycles after read +# bit15-12: 0100, internal ODT assertion 4 cycles after read +# bit19-16: 1000, internal ODT de-assertion 8 cycles after read +# bit31-20: 0 , required + +DATA 0xFFD0147c 0x00008451 # DDR2 SDRAM Timing High +# bit3-0 : 0001, M_ODT assertion same cycle as write +# bit7-4 : 0101, M_ODT de-assertion x cycles after write +# bit11-8 : 0100, internal ODT assertion x cycles after write +# bit15-12: 1000, internal ODT de-assertion x cycles after write + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x0F, Size (i.e. 256MB) + +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low) +# bit3-0: 0, ODT0Rd, MODT[0] not asserted during read from DRAM CS0 +# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 + +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above +# bit3-2: 00, ODT1 controlled by register +# bit31-4: zero, required + +DATA 0xFFD0149C 0x0000F801 # CPU ODT Control +# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0 +# bit7-4: 0, ODT0Wr, Internal ODT not asserted during write to DRAM bank0 +# bit9-8: 0, ODTEn, controlled by ODT0Rd and ODT0Wr +# bit11-10:2, DQ_ODTSel. ODT select turned on, 75 ohm +# bit13-12:3, STARTBURST ODT buffer selected, 50 ohm +# bit14 :1, STARTBURST ODT enabled +# bit15 :1, Use ODT Block + +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +# bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 diff --git a/roms/u-boot/board/keymile/km_arm/kwbimage.cfg b/roms/u-boot/board/keymile/km_arm/kwbimage.cfg new file mode 100644 index 000000000..6b62ce0ab --- /dev/null +++ b/roms/u-boot/board/keymile/km_arm/kwbimage.cfg @@ -0,0 +1,161 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# (C) Copyright 2010 +# Heiko Schocher, DENX Software Engineering, hs@denx.de. +# Refer doc/README.kwbimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM spi # Boot from SPI flash + +DATA 0xFFD10000 0x01112222 # MPP Control 0 Register +# bit 3-0: MPPSel0 2, NF_IO[2] +# bit 7-4: MPPSel1 2, NF_IO[3] +# bit 12-8: MPPSel2 2, NF_IO[4] +# bit 15-12: MPPSel3 2, NF_IO[5] +# bit 19-16: MPPSel4 1, NF_IO[6] +# bit 23-20: MPPSel5 1, NF_IO[7] +# bit 27-24: MPPSel6 1, SYSRST_O +# bit 31-28: MPPSel7 0, GPO[7] + +DATA 0xFFD10004 0x03303300 + +DATA 0xFFD10008 0x00001100 # MPP Control 2 Register +# bit 3-0: MPPSel16 0, GPIO[16] +# bit 7-4: MPPSel17 0, GPIO[17] +# bit 12-8: MPPSel18 1, NF_IO[0] +# bit 15-12: MPPSel19 1, NF_IO[1] +# bit 19-16: MPPSel20 0, GPIO[20] +# bit 23-20: MPPSel21 0, GPIO[21] +# bit 27-24: MPPSel22 0, GPIO[22] +# bit 31-28: MPPSel23 0, GPIO[23] + +DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register +DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register +DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register + +# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched! +# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage + +#Dram initalization +DATA 0xFFD01400 0x43000400 # SDRAM Configuration Register +# bit13-0: 0x400 (DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x39543000 # DDR Controller Control Low +# bit 3-0: 0 reserved +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 3=recommended value for CL=3 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 6= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x34136552 # DDR Timing (Low) (active cycles value +1) +# bit3-0: TRAS lsbs +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000033 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x0000000D # DDR Address Control +# bit1-0: 01, Cs0width=x16 +# bit3-2: 11, Cs0size=1Gb +# bit5-4: 00, Cs2width=nonexistent +# bit7-6: 00, Cs1size =nonexistent +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000652 # DDR Mode +DATA 0xFFD01420 0x00000044 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 0, DDR drive strenght normal +# bit2: 1, DDR ODT control lsd disabled +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, enabled +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F07F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 0 +# bit8 : 0 , no sample stage +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required +DATA 0xFFD01428 0x00074510 +DATA 0xFFD0147c 0x00007451 + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x07, Size (i.e. 128MB) + +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00010001 # DDR ODT Control (Low) +# bit3-0: 0, ODT0Rd, MODT[0] asserted during read from DRAM CS0 +# bit19-16:0, ODT0Wr, MODT[0] asserted during write to DRAM CS0 + +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above +# bit3-2: 00, ODT1 controlled by register +# bit31-4: zero, required + +DATA 0xFFD0149C 0x0000FC11 # CPU ODT Control +# bit3-0: F, ODT0Rd, Internal ODT asserted during read from DRAM bank0 +# bit7-4: 0, ODT0Wr, Internal ODT asserted during write to DRAM bank0 +# bit9-8: 1, ODTEn, never active +# bit11-10:2, DQ_ODTSel. ODT select turned on, 75 ohm + +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +# bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 diff --git a/roms/u-boot/board/keymile/km_arm/kwbimage_128M16_1.cfg b/roms/u-boot/board/keymile/km_arm/kwbimage_128M16_1.cfg new file mode 100644 index 000000000..e30c0feec --- /dev/null +++ b/roms/u-boot/board/keymile/km_arm/kwbimage_128M16_1.cfg @@ -0,0 +1,257 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# (C) Copyright 2010 +# Heiko Schocher, DENX Software Engineering, hs@denx.de. +# +# (C) Copyright 2012 +# Valentin Longchamp, Keymile AG, valentin.longchamp@keymile.com +# Stefan Bigler, Keymile AG, stefan.bigler@keymile.com +# +# (C) Copyright 2012 +# +# Refer doc/README.kwbimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM spi # Boot from SPI flash + +DATA 0xFFD10000 0x01112222 # MPP Control 0 Register +# bit 3-0: 2, MPPSel0 SPI_CSn (1=NF_IO[2]) +# bit 7-4: 2, MPPSel1 SPI_SI (1=NF_IO[3]) +# bit 12-8: 2, MPPSel2 SPI_SCK (1=NF_IO[4]) +# bit 15-12: 2, MPPSel3 SPI_SO (1=NF_IO[5]) +# bit 19-16: 1, MPPSel4 NF_IO[6] +# bit 23-20: 1, MPPSel5 NF_IO[7] +# bit 27-24: 1, MPPSel6 SYSRST_O +# bit 31-28: 0, MPPSel7 GPO[7] + +DATA 0xFFD10004 0x03303300 # MPP Control 1 Register +# bit 3-0: 0, MPPSel8 GPIO[8] +# bit 7-4: 0, MPPSel9 GPIO[9] +# bit 12-8: 3, MPPSel10 UA0_TXD +# bit 15-12: 3, MPPSel11 UA0_RXD +# bit 19-16: 0, MPPSel12 not connected +# bit 23-20: 3, MPPSel13 UA1_TXD +# bit 27-24: 3, MPPSel14 UA1_RXD +# bit 31-28: 0, MPPSel15 GPIO[15] + +DATA 0xFFD10008 0x00001100 # MPP Control 2 Register +# bit 3-0: 0, MPPSel16 GPIO[16] +# bit 7-4: 0, MPPSel17 not connected +# bit 12-8: 1, MPPSel18 NF_IO[0] +# bit 15-12: 1, MPPSel19 NF_IO[1] +# bit 19-16: 0, MPPSel20 GPIO[20] +# bit 23-20: 0, MPPSel21 GPIO[21] +# bit 27-24: 0, MPPSel22 GPIO[22] +# bit 31-28: 0, MPPSel23 GPIO[23] + +# MPP Control 3-6 Register untouched (MPP24-49) + +DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register +# bit 2-0: 3, Reserved +# bit 5-3: 3, Reserved +# bit 6: 0, Reserved +# bit 7: 0, RGMII-pads voltage = 3.3V +# bit 10-8: 3, Reserved +# bit 13-11: 3, Reserved +# bit 14: 0, Reserved +# bit 15: 0, MPP RGMII-pads voltage = 3.3V +# bit 31-16 0x1B1B, Reserved + +DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register +# bit 0-1: 2, Tag RAM RTC RAM0 +# bit 3-2: 1, Tag RAM WTC RAM0 +# bit 7-4: 6, Reserve +# bit 9-8: 2, Valid RAM RTC RAM +# bit 11-10: 1, Valid RAM WTC RAM +# bit 13-12: 2, Dirty RAM RTC RAM +# bit 15-14: 1, Dirty RAM WTC RAM +# bit 17-16: 2, Data RAM RTC RAM0 +# bit 19-18: 1, Data RAM WTC RAM0 +# bit 21-20: 2, Data RAM RTC RAM1 +# bit 23-22: 1, Data RAM WTC RAM1 +# bit 25-24: 2, Data RAM RTC RAM2 +# bit 27-26: 1, Data RAM WTC RAM2 +# bit 29-28: 2, Data RAM RTC RAM3 +# bit 31-30: 1, Data RAM WTC RAM4 + +DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register +# bit 15-0: ???, Reserve +# bit 17-16: 2, ECC RAM RTC RAM0 +# bit 19-18: 1, ECC RAM WTC RAM0 +# bit 31-20: ???,Reserve + +# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched! +# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage + +# SDRAM initalization +DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register +# bit 13-0: 0x4E0, DDR2 clks refresh rate +# bit 14: 0, reserved +# bit 15: 0, reserved +# bit 16: 0, CPU to Dram Write buffer policy +# bit 17: 0, Enable Registered DIMM or Equivalent Sampling Logic +# bit 19-18: 0, reserved +# bit 23-20: 0, reserved +# bit 24: 1, enable exit self refresh mode on DDR access +# bit 25: 1, required +# bit 29-26: 0, reserved +# bit 31-30: 1, reserved + +DATA 0xFFD01404 0x36543000 # DDR Controller Control Low +# bit 3-0: 0, reserved +# bit 4: 0, 2T mode =addr/cmd in same cycle +# bit 5: 0, clk is driven during self refresh, we don't care for APX +# bit 6: 0, use recommended falling edge of clk for addr/cmd +# bit 7-11: 0, reserved +# bit 12-13: 1, reserved, required 1 +# bit 14: 0, input buffer always powered up +# bit 17-15: 0, reserved +# bit 18: 1, cpu lock transaction enabled +# bit 19: 0, reserved +# bit 23-20: 5, recommended value for CL=4 and STARTBURST_DEL disabled bit31=0 +# bit 27-24: 6, CL+1, STARTBURST sample stages, for freqs 200-399MHz, unbuffered DIMM +# bit 30-28: 3, required +# bit 31: 0,no additional STARTBURST delay + +DATA 0xFFD01408 0x2302444e # DDR Timing (Low) (active cycles value +1) +# bit 3-0: 0xE, TRAS, 15 clk (45 ns) +# bit 7-4: 0x4, TRCD, 5 clk (15 ns) +# bit 11-8: 0x4, TRP, 5 clk (15 ns) +# bit 15-12: 0x4, TWR, 5 clk (15 ns) +# bit 19-16: 0x2, TWTR, 3 clk (7.5 ns) +# bit 20: 0, extended TRAS msb +# bit 23-21: 0, reserved +# bit 27-24: 0x3, TRRD, 4 clk (10 ns) +# bit 31-28: 0x2, TRTP, 3 clk (7.5 ns) + +DATA 0xFFD0140C 0x0000003e # DDR Timing (High) +# bit 6-0: 0x3E, TRFC, 63 clk (195 ns) +# bit 8-7: 0, TR2R +# bit 10-9: 0, TR2W +# bit 12-11: 0, TW2W +# bit 31-13: 0, reserved + +DATA 0xFFD01410 0x00000001 # DDR Address Control +# bit 1-0: 1, Cs0width=x16 +# bit 3-2: 0, Cs0size=2Gb +# bit 5-4: 0, Cs1width=nonexistent +# bit 7-6: 0, Cs1size =nonexistent +# bit 9-8: 0, Cs2width=nonexistent +# bit 11-10: 0, Cs2size =nonexistent +# bit 13-12: 0, Cs3width=nonexistent +# bit 15-14: 0, Cs3size =nonexistent +# bit 16: 0, Cs0AddrSel +# bit 17: 0, Cs1AddrSel +# bit 18: 0, Cs2AddrSel +# bit 19: 0, Cs3AddrSel +# bit 31-20: 0, required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit 0: 0, OpenPage enabled +# bit 31-1: 0, required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit 3-0: 0, DDR cmd +# bit 31-4: 0, required + +DATA 0xFFD0141C 0x00000652 # DDR Mode +# bit 2-0: 2, Burst Length = 4 +# bit 3: 0, Burst Type +# bit 6-4: 5, CAS Latency = 5 +# bit 7: 0, Test mode +# bit 8: 0, DLL Reset +# bit 11-9: 3, Write recovery for auto-precharge must be 3 +# bit 12: 0, Active power down exit time, fast exit +# bit 14-13: 0, reserved +# bit 31-15: 0, reserved + +DATA 0xFFD01420 0x00000006 # DDR Extended Mode +# bit 0: 0, DDR DLL enabled +# bit 1: 1, DDR drive strength reduced +# bit 2: 1, DDR ODT control lsb, 75 ohm termination [RTT0] +# bit 5-3: 0, required +# bit 6: 0, DDR ODT control msb, 75 ohm termination [RTT1] +# bit 9-7: 0, required +# bit 10: 0, differential DQS enabled +# bit 11: 0, required +# bit 12: 0, DDR output buffer enabled +# bit 31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit 2-0: 7, required +# bit 3: 1, MBUS Burst Chop disabled +# bit 6-4: 7, required +# bit 7: 0, reserved +# bit 8: 1, add sample stage required for f > 266 MHz +# bit 9: 0, no half clock cycle addition to dataout +# bit 10: 0, 1/4 clock cycle skew enabled for addr/ctl signals +# bit 11: 0, 1/4 clock cycle skew disabled for write mesh +# bit 15-12:0xf, required +# bit 31-16: 0, required + +DATA 0xFFD01428 0x00084520 # DDR2 SDRAM Timing Low +# bit 3-0: 0, required +# bit 7-4: 2, M_ODT assertion 2 cycles after read start command +# bit 11-8: 5, M_ODT de-assertion 5 cycles after read start command +# (ODT turn off delay 2,5 clk cycles) +# bit 15-12: 4, internal ODT time based on bit 7-4 +# with the considered SDRAM internal delay +# bit 19-16: 8, internal ODT de-assertion based on bit 11-8 +# with the considered SDRAM internal delay +# bit 31-20: 0, required + +DATA 0xFFD0147c 0x00008452 # DDR2 SDRAM Timing High +# bit 3-0: 2, M_ODT assertion same as bit 11-8 +# bit 7-4: 5, M_ODT de-assertion same as bit 15-12 +# bit 11-8: 4, internal ODT assertion 2 cycles after write start command +# with the considered SDRAM internal delay +# bit 15-12: 8, internal ODT de-assertion 5 cycles after write start command +# with the considered SDRAM internal delay + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +# bit 23-0: 0, reserved +# bit 31-24: 0, CPU CS Window0 Base Address, addr bits [31:24] + +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size +# bit 0: 1, Window enabled +# bit 1: 0, Write Protect disabled +# bit 3-2: 0, CS0 hit selected +# bit 23-4:ones, required +# bit 31-24: 0x0F, Size (i.e. 256MB) + +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low) +# bit 3-0: 0, ODT0Rd, MODT[0] not asserted during read from DRAM CS0 +# bit 7-4: 0, ODT0Rd, MODT[1] not asserted +# bit 11-8: 0, required +# big 15-11: 0, required +# bit 19-16: 1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 +# bit 23-20: 0, ODT0Wr, MODT[1] not asserted +# bit 27-24: 0, required +# bit 31-28: 0, required + +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit 1-0: 0, ODT0 controlled by ODT Control (low) register above +# bit 3-2: 0, ODT1 controlled by register +# bit 31-4: 0, required + +DATA 0xFFD0149C 0x0000E801 # CPU ODT Control +# bit 3-0: 1, ODTRd, Internal ODT asserted during read from DRAM bank0 +# bit 7-4: 0, ODTWr, Internal ODT not asserted during write to DRAM +# bit 9-8: 0, ODTEn, controlled by ODTRd and ODTWr +# bit 11-10: 2, DQ_ODTSel. ODT select turned on, 75 ohm +# bit 13-12: 2, STARTBURST ODT buffer selected, 75 ohm +# bit 14: 1, STARTBURST ODT enabled +# bit 15: 1, Use ODT Block + +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +# bit 0: 1, enable DDR init upon this register write +# bit 31-1: 0, reserved + +# End of Header extension +DATA 0x0 0x0 diff --git a/roms/u-boot/board/keymile/km_arm/kwbimage_256M8_1.cfg b/roms/u-boot/board/keymile/km_arm/kwbimage_256M8_1.cfg new file mode 100644 index 000000000..91ea5f007 --- /dev/null +++ b/roms/u-boot/board/keymile/km_arm/kwbimage_256M8_1.cfg @@ -0,0 +1,257 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# (C) Copyright 2012 +# Stefan Bigler, Keymile AG, stefan.bigler@keymile.com +# Norbert Mayer, Keymile AG, norbert.mayer@keymile.com +# Deepak Patel, XENTECH Limited, deepak.patel@xentech.co.uk +# Refer doc/README.kwbimage for more details about how-to configure +# and create kirkwood boot image +# +# This configuration applies to COGE5 design (ARM-part) +# Two 8-Bit devices are connected on the 16-Bit bus on the same +# chip-select. The supported devices are +# MT47H256M8EB-3IT:C +# MT47H256M8EB-25EIT:C + +# Boot Media configurations +BOOT_FROM spi # Boot from SPI flash + +DATA 0xFFD10000 0x01112222 # MPP Control 0 Register +# bit 3-0: 2, MPPSel0 SPI_CSn (1=NF_IO[2]) +# bit 7-4: 2, MPPSel1 SPI_MOSI (1=NF_IO[3]) +# bit 12-8: 2, MPPSel2 SPI_SCK (1=NF_IO[4]) +# bit 15-12: 2, MPPSel3 SPI_MISO (1=NF_IO[5]) +# bit 19-16: 1, MPPSel4 NF_IO[6] +# bit 23-20: 1, MPPSel5 NF_IO[7] +# bit 27-24: 1, MPPSel6 SYSRST_O +# bit 31-28: 0, MPPSel7 GPO[7] + +DATA 0xFFD10004 0x03303300 # MPP Control 1 Register +# bit 3-0: 0, MPPSel8 GPIO[8] CPU_SDA bitbanged +# bit 7-4: 0, MPPSel9 GPIO[9] CPU_SCL bitbanged +# bit 12-8: 3, MPPSel10 UA0_TXD +# bit 15-12: 3, MPPSel11 UA0_RXD +# bit 19-16: 0, MPPSel12 not connected +# bit 23-20: 3, MPPSel13 GPIO[14] +# bit 27-24: 3, MPPSel14 GPIO[15] +# bit 31-28: 0, MPPSel15 GPIO[16] BOOT_FL_SEL (SPI-MUX Signal) + +DATA 0xFFD10008 0x00001100 # MPP Control 2 Register +# bit 3-0: 0, MPPSel16 GPIO[16] +# bit 7-4: 0, MPPSel17 not connected +# bit 11-8: 1, MPPSel18 NF_IO[0] +# bit 15-12: 1, MPPSel19 NF_IO[1] +# bit 19-16: 0, MPPSel20 GPIO[20] +# bit 23-20: 0, MPPSel21 GPIO[21] +# bit 27-24: 0, MPPSel22 GPIO[22] +# bit 31-28: 0, MPPSel23 GPIO[23] + +# MPP Control 3-6 Register untouched (MPP24-49) + +DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register +# bit 2-0: 3, Reserved +# bit 5-3: 3, Reserved +# bit 6: 0, Reserved +# bit 7: 0, RGMII-pads voltage = 3.3V +# bit 10-8: 3, Reserved +# bit 13-11: 3, Reserved +# bit 14: 0, Reserved +# bit 15: 0, MPP RGMII-pads voltage = 3.3V +# bit 31-16 0x1B1B, Reserved + +DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register +# bit 0-1: 2, Tag RAM RTC RAM0 +# bit 3-2: 1, Tag RAM WTC RAM0 +# bit 7-4: 6, Reserved +# bit 9-8: 2, Valid RAM RTC RAM +# bit 11-10: 1, Valid RAM WTC RAM +# bit 13-12: 2, Dirty RAM RTC RAM +# bit 15-14: 1, Dirty RAM WTC RAM +# bit 17-16: 2, Data RAM RTC RAM0 +# bit 19-18: 1, Data RAM WTC RAM0 +# bit 21-20: 2, Data RAM RTC RAM1 +# bit 23-22: 1, Data RAM WTC RAM1 +# bit 25-24: 2, Data RAM RTC RAM2 +# bit 27-26: 1, Data RAM WTC RAM2 +# bit 29-28: 2, Data RAM RTC RAM3 +# bit 31-30: 1, Data RAM WTC RAM4 + +DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register +# bit 15-0: ?, Reserved +# bit 17-16: 2, ECC RAM RTC RAM0 +# bit 19-18: 1, ECC RAM WTC RAM0 +# bit 31-20: ?,Reserved + +# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched! +# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage + +# SDRAM initalization +DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register +# bit 13-0: 0x4E0, DDR2 clks refresh rate +# bit 14: 0, reserved +# bit 15: 0, reserved +# bit 16: 0, CPU to Dram Write buffer policy +# bit 17: 0, Enable Registered DIMM or Equivalent Sampling Logic +# bit 19-18: 0, reserved +# bit 23-20: 0, reserved +# bit 24: 1, enable exit self refresh mode on DDR access +# bit 25: 1, required +# bit 29-26: 0, reserved +# bit 31-30: 1, reserved + +DATA 0xFFD01404 0x36543000 # DDR Controller Control Low +# bit 3-0: 0, reserved +# bit 4: 0, 2T mode =addr/cmd in same cycle +# bit 5: 0, clk is driven during self refresh, we don't care for APX +# bit 6: 0, use recommended falling edge of clk for addr/cmd +# bit 7-11: 0, reserved +# bit 12-13: 1, reserved, required 1 +# bit 14: 0, input buffer always powered up +# bit 17-15: 0, reserved +# bit 18: 1, cpu lock transaction enabled +# bit 19: 0, reserved +# bit 23-20: 5, recommended value for CL=4 and STARTBURST_DEL disabled bit31=0 +# bit 27-24: 6, CL+1, STARTBURST sample stages, freq 200-399MHz, unbuffer DIMM +# bit 30-28: 3, required +# bit 31: 0, no additional STARTBURST delay + +DATA 0xFFD01408 0x2202444E # DDR Timing (Low) (active cycles value +1) +# bit 3-0: 0xe, TRAS = 45ns -> 15 clk cycles +# bit 7-4: 0x4, TRCD = 15ns -> 5 clk cycles +# bit 11-8: 0x4, TRP = 15ns -> 5 clk cycles +# bit 15-12: 0x4, TWR = 15ns -> 5 clk cycles +# bit 19-16: 0x2, TWTR = 7,5ns -> 3 clk cycles +# bit 20: 0, extended TRAS msb +# bit 23-21: 0, reserved +# bit 27-24: 0x2, TRRD = 7,5ns -> 3 clk cycles +# bit 31-28: 0x2, TRTP = 7,5ns -> 3 clk cycles + +DATA 0xFFD0140C 0x0000003E # DDR Timing (High) +# bit 6-0: 0x3E, TRFC = 195ns -> 63 clk cycles +# bit 8-7: 0, TR2R +# bit 10-9: 0, TR2W +# bit 12-11: 0, TW2W +# bit 31-13: 0, reserved + +DATA 0xFFD01410 0x00000000 # DDR Address Control +# bit 1-0: 0, Cs0width=x8 (2 devices) +# bit 3-2: 0, Cs0size=2Gb +# bit 5-4: 0, Cs1width=nonexistent +# bit 7-6: 0, Cs1size =nonexistent +# bit 9-8: 0, Cs2width=nonexistent +# bit 11-10: 0, Cs2size =nonexistent +# bit 13-12: 0, Cs3width=nonexistent +# bit 15-14: 0, Cs3size =nonexistent +# bit 16: 0, Cs0AddrSel +# bit 17: 0, Cs1AddrSel +# bit 18: 0, Cs2AddrSel +# bit 19: 0, Cs3AddrSel +# bit 31-20: 0, required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit 0: 0, OpenPage enabled +# bit 31-1: 0, required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit 3-0: 0, DDR cmd +# bit 31-4: 0, required + +DATA 0xFFD0141C 0x00000652 # DDR Mode +# bit 2-0: 2, Burst Length = 4 +# bit 3: 0, Burst Type +# bit 6-4: 5, CAS Latency = 5 +# bit 7: 0, Test mode +# bit 8: 0, DLL Reset +# bit 11-9: 3, Write recovery for auto-precharge must be 3 +# bit 12: 0, Active power down exit time, fast exit +# bit 14-13: 0, reserved +# bit 31-15: 0, reserved + +DATA 0xFFD01420 0x00000006 # DDR Extended Mode +# bit 0: 0, DDR DLL enabled +# bit 1: 1, DDR drive strenght reduced +# bit 2: 1, DDR ODT control lsb, 75ohm termination [RTT0] +# bit 5-3: 0, required +# bit 6: 0, DDR ODT control msb, 75ohm termination [RTT1] +# bit 9-7: 0, required +# bit 10: 0, differential DQS enabled +# bit 11: 0, required +# bit 12: 0, DDR output buffer enabled +# bit 31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit 2-0: 7, required +# bit 3: 1, MBUS Burst Chop disabled +# bit 6-4: 7, required +# bit 7: 0, reserved +# bit 8: 1, add sample stage required for > 266Mhz +# bit 9: 0, no half clock cycle addition to dataout +# bit 10: 0, 1/4 clock cycle skew enabled for addr/ctl signals +# bit 11: 0, 1/4 clock cycle skew disabled for write mesh +# bit 15-12:0xf, required +# bit 31-16: 0, required + +DATA 0xFFD01428 0x00084520 # DDR2 SDRAM Timing Low +# bit 3-0: 0, required +# bit 7-4: 2, M_ODT assertion 2 cycles after read start command +# bit 11-8: 5, M_ODT de-assertion 5 cycles after read start command +# (ODT turn off delay 2,5 clk cycles) +# bit 15-12: 4, internal ODT time based on bit 7-4 +# with the considered SDRAM internal delay +# bit 19-16: 8, internal ODT de-assertion based on bit 11-8 +# with the considered SDRAM internal delay +# bit 31-20: 0, required + +DATA 0xFFD0147c 0x00008452 # DDR2 SDRAM Timing High +# bit 3-0: 2, M_ODT assertion same as bit 11-8 +# bit 7-4: 5, M_ODT de-assertion same as bit 15-12 +# bit 11-8: 4, internal ODT assertion 2 cycles after write start command +# with the considered SDRAM internal delay +# bit 15-12: 8, internal ODT de-assertion 5 cycles after write start command +# with the considered SDRAM internal delay + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +# bit 23-0: 0, reserved +# bit 31-24: 0, CPU CS Window0 Base Address, addr bits [31:24] + +DATA 0xFFD01504 0x1FFFFFF1 # CS[0]n Size +# bit 0: 1, Window enabled +# bit 1: 0, Write Protect disabled +# bit 3-2: 0, CS0 hit selected +# bit 23-4:ones, required +# bit 31-24:0x1F, Size (i.e. 512MB) + +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low) +# bit 3-0: 0, ODT0Rd, MODT[0] not asserted during read from DRAM CS0 +# bit 7-4: 0, ODT0Rd, MODT[1] not asserted +# bit 11-8: 0, required +# big 15-11: 0, required +# bit 19-16: 1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 +# bit 23-20: 0, ODT0Wr, MODT[1] not asserted +# bit 27-24: 0, required +# bit 31-28: 0, required + +DATA 0xFFD01498 0x00000004 # DDR ODT Control (High) +# bit 1-0: 0, ODT0 controlled by ODT Control (low) register above +# bit 3-2: 1, ODT1 never active +# bit 31-4: 0, required + +DATA 0xFFD0149C 0x0000E801 # CPU ODT Control +# bit 3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0 +# bit 7-4: 0, ODT0Wr, Internal ODT not asserted during write to DRAM bank0 +# bit 9-8: 0, ODTEn, controlled by ODT0Rd and ODT0Wr +# bit 11-10: 2, DQ_ODTSel. ODT select turned on, 75 ohm +# bit 13-12: 2, STARTBURST ODT buffer selected, 75 ohm +# bit 14: 1, STARTBURST ODT enabled +# bit 15: 1, Use ODT Block + +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +# bit 0: 1, enable DDR init upon this register write +# bit 31-1: 0, reserved + +# End of Header extension +DATA 0x0 0x0 |