1 files changed, 338 insertions, 0 deletions
diff --git a/roms/u-boot/board/samsung/trats2/trats2.c b/roms/u-boot/board/samsung/trats2/trats2.c
new file mode 100644
index 000000000..59e6fbf4b
--- /dev/null
+++ b/roms/u-boot/board/samsung/trats2/trats2.c
@@ -0,0 +1,338 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd. All rights reserved.
+ * Sanghee Kim <sh0130.kim@samsung.com>
+ * Piotr Wilczek <p.wilczek@samsung.com>
+ */
+
+#include <common.h>
+#include <lcd.h>
+#include <log.h>
+#include <asm/gpio.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/power.h>
+#include <asm/arch/mipi_dsim.h>
+#include <linux/delay.h>
+#include <power/pmic.h>
+#include <power/max77686_pmic.h>
+#include <power/battery.h>
+#include <power/max77693_pmic.h>
+#include <power/max77693_muic.h>
+#include <power/max77693_fg.h>
+#include <libtizen.h>
+#include <errno.h>
+#include <usb.h>
+#include <usb/dwc2_udc.h>
+#include <usb_mass_storage.h>
+
+static unsigned int board_rev = -1;
+
+static inline u32 get_model_rev(void);
+
+static void check_hw_revision(void)
+{
+	int modelrev = 0;
+	char str[12];
+	int i;
+
+	/*
+	 * GPM1[1:0]: MODEL_REV[1:0]
+	 * Don't set as pull-none for these N/C pin.
+	 * TRM say that it may cause unexcepted state and leakage current.
+	 * and pull-none is only for output function.
+	 */
+	for (i = 0; i < 2; i++) {
+		int pin = i + EXYNOS4X12_GPIO_M10;
+
+		sprintf(str, "model_rev%d", i);
+		gpio_request(pin, str);
+		gpio_cfg_pin(pin, S5P_GPIO_INPUT);
+	}
+
+	/* GPM1[5:2]: HW_REV[3:0] */
+	for (i = 0; i < 4; i++) {
+		int pin = i + EXYNOS4X12_GPIO_M12;
+
+		sprintf(str, "hw_rev%d", i);
+		gpio_request(pin, str);
+		gpio_cfg_pin(pin, S5P_GPIO_INPUT);
+		gpio_set_pull(pin, S5P_GPIO_PULL_NONE);
+	}
+
+	/* GPM1[1:0]: MODEL_REV[1:0] */
+	for (i = 0; i < 2; i++)
+		modelrev |= (gpio_get_value(EXYNOS4X12_GPIO_M10 + i) << i);
+
+	/* board_rev[15:8] = model */
+	board_rev = modelrev << 8;
+}
+
+u32 get_board_rev(void)
+{
+	return board_rev;
+}
+
+static inline u32 get_model_rev(void)
+{
+	return (board_rev >> 8) & 0xff;
+}
+
+static void board_external_gpio_init(void)
+{
+	/*
+	 * some pins which in alive block are connected with external pull-up
+	 * but it's default setting is pull-down.
+	 * if that pin set as input then that floated
+	 */
+
+	gpio_set_pull(EXYNOS4X12_GPIO_X02, S5P_GPIO_PULL_NONE);	/* PS_ALS_INT */
+	gpio_set_pull(EXYNOS4X12_GPIO_X04, S5P_GPIO_PULL_NONE);	/* TSP_nINT */
+	gpio_set_pull(EXYNOS4X12_GPIO_X07, S5P_GPIO_PULL_NONE);	/* AP_PMIC_IRQ*/
+	gpio_set_pull(EXYNOS4X12_GPIO_X15, S5P_GPIO_PULL_NONE);	/* IF_PMIC_IRQ*/
+	gpio_set_pull(EXYNOS4X12_GPIO_X20, S5P_GPIO_PULL_NONE);	/* VOL_UP */
+	gpio_set_pull(EXYNOS4X12_GPIO_X21, S5P_GPIO_PULL_NONE);	/* VOL_DOWN */
+	gpio_set_pull(EXYNOS4X12_GPIO_X23, S5P_GPIO_PULL_NONE);	/* FUEL_ALERT */
+	gpio_set_pull(EXYNOS4X12_GPIO_X24, S5P_GPIO_PULL_NONE);	/* ADC_INT */
+	gpio_set_pull(EXYNOS4X12_GPIO_X27, S5P_GPIO_PULL_NONE);	/* nPOWER */
+	gpio_set_pull(EXYNOS4X12_GPIO_X30, S5P_GPIO_PULL_NONE);	/* WPC_INT */
+	gpio_set_pull(EXYNOS4X12_GPIO_X35, S5P_GPIO_PULL_NONE);	/* OK_KEY */
+	gpio_set_pull(EXYNOS4X12_GPIO_X37, S5P_GPIO_PULL_NONE);	/* HDMI_HPD */
+}
+
+int exynos_early_init_f(void)
+{
+	board_external_gpio_init();
+
+	return 0;
+}
+
+int exynos_init(void)
+{
+	struct exynos4_power *pwr =
+		(struct exynos4_power *)samsung_get_base_power();
+
+	check_hw_revision();
+	printf("HW Revision:\t0x%04x\n", board_rev);
+
+	/*
+	 * First bootloader on the TRATS2 platform uses
+	 * INFORM4 and INFORM5 registers for recovery
+	 *
+	 * To indicate correct boot chain - those two
+	 * registers must be cleared out
+	 */
+	writel(0, &pwr->inform4);
+	writel(0, &pwr->inform5);
+
+	return 0;
+}
+
+int exynos_power_init(void)
+{
+#if !CONFIG_IS_ENABLED(DM_I2C) /* TODO(maintainer): Convert to driver model */
+	int chrg;
+	struct power_battery *pb;
+	struct pmic *p_chrg, *p_muic, *p_fg, *p_bat;
+
+	pmic_init_max77693(I2C_10);	/* I2C adapter 10 - bus name soft1 */
+	power_muic_init(I2C_10);	/* I2C adapter 10 - bus name soft1 */
+	power_fg_init(I2C_9);		/* I2C adapter 9 - bus name soft0 */
+	power_bat_init(0);
+
+	p_chrg = pmic_get("MAX77693_PMIC");
+	if (!p_chrg) {
+		puts("MAX77693_PMIC: Not found\n");
+		return -ENODEV;
+	}
+
+	p_muic = pmic_get("MAX77693_MUIC");
+	if (!p_muic) {
+		puts("MAX77693_MUIC: Not found\n");
+		return -ENODEV;
+	}
+
+	p_fg = pmic_get("MAX77693_FG");
+	if (!p_fg) {
+		puts("MAX17042_FG: Not found\n");
+		return -ENODEV;
+	}
+
+	if (p_chrg->chrg->chrg_bat_present(p_chrg) == 0)
+		puts("No battery detected\n");
+
+	p_bat = pmic_get("BAT_TRATS2");
+	if (!p_bat) {
+		puts("BAT_TRATS2: Not found\n");
+		return -ENODEV;
+	}
+
+	p_fg->parent =  p_bat;
+	p_chrg->parent = p_bat;
+	p_muic->parent = p_bat;
+
+	p_bat->pbat->battery_init(p_bat, p_fg, p_chrg, p_muic);
+
+	pb = p_bat->pbat;
+	chrg = p_muic->chrg->chrg_type(p_muic);
+	debug("CHARGER TYPE: %d\n", chrg);
+
+	if (!p_chrg->chrg->chrg_bat_present(p_chrg)) {
+		puts("No battery detected\n");
+		return 0;
+	}
+
+	p_fg->fg->fg_battery_check(p_fg, p_bat);
+
+	if (pb->bat->state == CHARGE && chrg == CHARGER_USB)
+		puts("CHARGE Battery !\n");
+#endif
+	return 0;
+}
+
+#ifdef CONFIG_USB_GADGET
+static int s5pc210_phy_control(int on)
+{
+#if !CONFIG_IS_ENABLED(DM_I2C) /* TODO(maintainer): Convert to driver model */
+	int ret = 0;
+	unsigned int val;
+	struct pmic *p, *p_pmic, *p_muic;
+
+	p_pmic = pmic_get("MAX77686_PMIC");
+	if (!p_pmic)
+		return -ENODEV;
+
+	if (pmic_probe(p_pmic))
+		return -1;
+
+	p_muic = pmic_get("MAX77693_MUIC");
+	if (!p_muic)
+		return -ENODEV;
+
+	if (pmic_probe(p_muic))
+		return -1;
+
+	if (on) {
+		ret = max77686_set_ldo_mode(p_pmic, 12, OPMODE_ON);
+		if (ret)
+			return -1;
+
+		p = pmic_get("MAX77693_PMIC");
+		if (!p)
+			return -ENODEV;
+
+		if (pmic_probe(p))
+			return -1;
+
+		/* SAFEOUT */
+		ret = pmic_reg_read(p, MAX77693_SAFEOUT, &val);
+		if (ret)
+			return -1;
+
+		val |= MAX77693_ENSAFEOUT1;
+		ret = pmic_reg_write(p, MAX77693_SAFEOUT, val);
+		if (ret)
+			return -1;
+
+		/* PATH: USB */
+		ret = pmic_reg_write(p_muic, MAX77693_MUIC_CONTROL1,
+			MAX77693_MUIC_CTRL1_DN1DP2);
+
+	} else {
+		ret = max77686_set_ldo_mode(p_pmic, 12, OPMODE_LPM);
+		if (ret)
+			return -1;
+
+		/* PATH: UART */
+		ret = pmic_reg_write(p_muic, MAX77693_MUIC_CONTROL1,
+			MAX77693_MUIC_CTRL1_UT1UR2);
+	}
+
+	if (ret)
+		return -1;
+#endif
+	return 0;
+}
+
+struct dwc2_plat_otg_data s5pc210_otg_data = {
+	.phy_control	= s5pc210_phy_control,
+	.regs_phy	= EXYNOS4X12_USBPHY_BASE,
+	.regs_otg	= EXYNOS4X12_USBOTG_BASE,
+	.usb_phy_ctrl	= EXYNOS4X12_USBPHY_CONTROL,
+	.usb_flags	= PHY0_SLEEP,
+};
+
+int board_usb_init(int index, enum usb_init_type init)
+{
+	debug("USB_udc_probe\n");
+	return dwc2_udc_probe(&s5pc210_otg_data);
+}
+
+int g_dnl_board_usb_cable_connected(void)
+{
+#if !CONFIG_IS_ENABLED(DM_I2C) /* TODO(maintainer): Convert to driver model */
+	struct pmic *muic = pmic_get("MAX77693_MUIC");
+	if (!muic)
+		return 0;
+
+	return !!muic->chrg->chrg_type(muic);
+#else
+	return false;
+#endif
+}
+#endif
+
+/*
+ * LCD
+ */
+
+#ifdef CONFIG_LCD
+int mipi_power(void)
+{
+#if !CONFIG_IS_ENABLED(DM_I2C) /* TODO(maintainer): Convert to driver model */
+	struct pmic *p = pmic_get("MAX77686_PMIC");
+
+	/* LDO8 VMIPI_1.0V_AP */
+	max77686_set_ldo_mode(p, 8, OPMODE_ON);
+	/* LDO10 VMIPI_1.8V_AP */
+	max77686_set_ldo_mode(p, 10, OPMODE_ON);
+#endif
+
+	return 0;
+}
+
+void exynos_lcd_power_on(void)
+{
+#if !CONFIG_IS_ENABLED(DM_I2C) /* TODO(maintainer): Convert to driver model */
+	struct pmic *p = pmic_get("MAX77686_PMIC");
+
+	/* LCD_2.2V_EN: GPC0[1] */
+	gpio_request(EXYNOS4X12_GPIO_C01, "lcd_2v2_en");
+	gpio_set_pull(EXYNOS4X12_GPIO_C01, S5P_GPIO_PULL_UP);
+	gpio_direction_output(EXYNOS4X12_GPIO_C01, 1);
+
+	/* LDO25 VCC_3.1V_LCD */
+	pmic_probe(p);
+	max77686_set_ldo_voltage(p, 25, 3100000);
+	max77686_set_ldo_mode(p, 25, OPMODE_LPM);
+#endif
+}
+
+void exynos_reset_lcd(void)
+{
+	/* reset lcd */
+	gpio_request(EXYNOS4X12_GPIO_F21, "lcd_reset");
+	gpio_direction_output(EXYNOS4X12_GPIO_F21, 0);
+	udelay(10);
+	gpio_set_value(EXYNOS4X12_GPIO_F21, 1);
+}
+
+void exynos_lcd_misc_init(vidinfo_t *vid)
+{
+#ifdef CONFIG_TIZEN
+	get_tizen_logo_info(vid);
+#endif
+#ifdef CONFIG_S6E8AX0
+	s6e8ax0_init();
+#endif
+}
+#endif /* LCD */