diff options
Diffstat (limited to 'roms/u-boot/board/udoo/neo/neo.c')
| -rw-r--r-- | roms/u-boot/board/udoo/neo/neo.c | 506 |
1 files changed, 506 insertions, 0 deletions
diff --git a/roms/u-boot/board/udoo/neo/neo.c b/roms/u-boot/board/udoo/neo/neo.c new file mode 100644 index 000000000..92a1e084b --- /dev/null +++ b/roms/u-boot/board/udoo/neo/neo.c @@ -0,0 +1,506 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2014-2015 Freescale Semiconductor, Inc. + * Copyright (C) Jasbir Matharu + * Copyright (C) UDOO Team + * + * Author: Breno Lima <breno.lima@nxp.com> + * Author: Francesco Montefoschi <francesco.monte@gmail.com> + */ + +#include <init.h> +#include <asm/arch/clock.h> +#include <asm/arch/crm_regs.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/iomux.h> +#include <asm/arch/mx6-pins.h> +#include <asm/global_data.h> +#include <asm/gpio.h> +#include <asm/mach-imx/iomux-v3.h> +#include <dm.h> +#include <env.h> +#include <asm/arch/crm_regs.h> +#include <asm/io.h> +#include <asm/mach-imx/mxc_i2c.h> +#include <asm/arch/sys_proto.h> +#include <spl.h> +#include <linux/delay.h> +#include <linux/sizes.h> +#include <common.h> +#include <i2c.h> +#include <power/pmic.h> +#include <power/pfuze3000_pmic.h> +#include <malloc.h> + +DECLARE_GLOBAL_DATA_PTR; + +enum { + UDOO_NEO_TYPE_BASIC, + UDOO_NEO_TYPE_BASIC_KS, + UDOO_NEO_TYPE_FULL, + UDOO_NEO_TYPE_EXTENDED, +}; + +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE) + +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ + PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + +#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST) + +#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_SPEED_MED | PAD_CTL_SRE_FAST) + +#define WDOG_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_PKE | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm) + +#define BOARD_DETECT_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_34ohm | PAD_CTL_HYS | PAD_CTL_SRE_FAST) +#define BOARD_DETECT_PAD_CFG (MUX_PAD_CTRL(BOARD_DETECT_PAD_CTRL) | \ + MUX_MODE_SION) + +int dram_init(void) +{ + gd->ram_size = imx_ddr_size(); + return 0; +} + +#ifdef CONFIG_SYS_I2C_MXC +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) +/* I2C1 for PMIC */ +static struct i2c_pads_info i2c_pad_info1 = { + .scl = { + .i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC, + .gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC, + .gp = IMX_GPIO_NR(1, 0), + }, + .sda = { + .i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC, + .gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC, + .gp = IMX_GPIO_NR(1, 1), + }, +}; +#endif + +#ifdef CONFIG_POWER +int power_init_board(void) +{ + struct pmic *p; + int ret; + unsigned int reg, rev_id; + + ret = power_pfuze3000_init(PFUZE3000_I2C_BUS); + if (ret) + return ret; + + p = pmic_get("PFUZE3000"); + ret = pmic_probe(p); + if (ret) + return ret; + + pmic_reg_read(p, PFUZE3000_DEVICEID, ®); + pmic_reg_read(p, PFUZE3000_REVID, &rev_id); + printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id); + + /* disable Low Power Mode during standby mode */ + pmic_reg_read(p, PFUZE3000_LDOGCTL, ®); + reg |= 0x1; + ret = pmic_reg_write(p, PFUZE3000_LDOGCTL, reg); + if (ret) + return ret; + + ret = pmic_reg_write(p, PFUZE3000_SW1AMODE, 0xc); + if (ret) + return ret; + + ret = pmic_reg_write(p, PFUZE3000_SW1BMODE, 0xc); + if (ret) + return ret; + + ret = pmic_reg_write(p, PFUZE3000_SW2MODE, 0xc); + if (ret) + return ret; + + ret = pmic_reg_write(p, PFUZE3000_SW3MODE, 0xc); + if (ret) + return ret; + + /* set SW1A standby voltage 0.975V */ + pmic_reg_read(p, PFUZE3000_SW1ASTBY, ®); + reg &= ~0x3f; + reg |= PFUZE3000_SW1AB_SETP(9750); + ret = pmic_reg_write(p, PFUZE3000_SW1ASTBY, reg); + if (ret) + return ret; + + /* set SW1B standby voltage 0.975V */ + pmic_reg_read(p, PFUZE3000_SW1BSTBY, ®); + reg &= ~0x3f; + reg |= PFUZE3000_SW1AB_SETP(9750); + ret = pmic_reg_write(p, PFUZE3000_SW1BSTBY, reg); + if (ret) + return ret; + + /* set SW1A/VDD_ARM_IN step ramp up time from 16us to 4us/25mV */ + pmic_reg_read(p, PFUZE3000_SW1ACONF, ®); + reg &= ~0xc0; + reg |= 0x40; + ret = pmic_reg_write(p, PFUZE3000_SW1ACONF, reg); + if (ret) + return ret; + + /* set SW1B/VDD_SOC_IN step ramp up time from 16us to 4us/25mV */ + pmic_reg_read(p, PFUZE3000_SW1BCONF, ®); + reg &= ~0xc0; + reg |= 0x40; + ret = pmic_reg_write(p, PFUZE3000_SW1BCONF, reg); + if (ret) + return ret; + + /* set VDD_ARM_IN to 1.350V */ + pmic_reg_read(p, PFUZE3000_SW1AVOLT, ®); + reg &= ~0x3f; + reg |= PFUZE3000_SW1AB_SETP(13500); + ret = pmic_reg_write(p, PFUZE3000_SW1AVOLT, reg); + if (ret) + return ret; + + /* set VDD_SOC_IN to 1.350V */ + pmic_reg_read(p, PFUZE3000_SW1BVOLT, ®); + reg &= ~0x3f; + reg |= PFUZE3000_SW1AB_SETP(13500); + ret = pmic_reg_write(p, PFUZE3000_SW1BVOLT, reg); + if (ret) + return ret; + + /* set DDR_1_5V to 1.350V */ + pmic_reg_read(p, PFUZE3000_SW3VOLT, ®); + reg &= ~0x0f; + reg |= PFUZE3000_SW3_SETP(13500); + ret = pmic_reg_write(p, PFUZE3000_SW3VOLT, reg); + if (ret) + return ret; + + /* set VGEN2_1V5 to 1.5V */ + pmic_reg_read(p, PFUZE3000_VLDO2CTL, ®); + reg &= ~0x0f; + reg |= PFUZE3000_VLDO_SETP(15000); + /* enable */ + reg |= 0x10; + ret = pmic_reg_write(p, PFUZE3000_VLDO2CTL, reg); + if (ret) + return ret; + + return 0; +} +#endif + +static iomux_v3_cfg_t const uart1_pads[] = { + MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static iomux_v3_cfg_t const phy_control_pads[] = { + /* 25MHz Ethernet PHY Clock */ + MX6_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M | + MUX_PAD_CTRL(ENET_CLK_PAD_CTRL), +}; + +static iomux_v3_cfg_t const board_recognition_pads[] = { + /*Connected to R184*/ + MX6_PAD_NAND_READY_B__GPIO4_IO_13 | BOARD_DETECT_PAD_CFG, + /*Connected to R185*/ + MX6_PAD_NAND_ALE__GPIO4_IO_0 | BOARD_DETECT_PAD_CFG, +}; + +static iomux_v3_cfg_t const wdog_b_pad = { + MX6_PAD_GPIO1_IO13__GPIO1_IO_13 | MUX_PAD_CTRL(WDOG_PAD_CTRL), +}; + +static iomux_v3_cfg_t const peri_3v3_pads[] = { + MX6_PAD_QSPI1A_DATA0__GPIO4_IO_16 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static void setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); +} + +static int setup_fec(void) +{ + struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; + int reg; + + imx_iomux_v3_setup_multiple_pads(phy_control_pads, + ARRAY_SIZE(phy_control_pads)); + + /* Reset PHY */ + gpio_direction_output(IMX_GPIO_NR(2, 1) , 0); + udelay(10000); + gpio_set_value(IMX_GPIO_NR(2, 1), 1); + udelay(100); + + reg = readl(&anatop->pll_enet); + reg |= BM_ANADIG_PLL_ENET_REF_25M_ENABLE; + writel(reg, &anatop->pll_enet); + + return enable_fec_anatop_clock(0, ENET_25MHZ); +} + +int board_init(void) +{ + /* Address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + + /* + * Because kernel set WDOG_B mux before pad with the commone pinctrl + * framwork now and wdog reset will be triggered once set WDOG_B mux + * with default pad setting, we set pad setting here to workaround this. + * Since imx_iomux_v3_setup_pad also set mux before pad setting, we set + * as GPIO mux firstly here to workaround it. + */ + imx_iomux_v3_setup_pad(wdog_b_pad); + + /* Enable PERI_3V3, which is used by SD2, ENET, LVDS, BT */ + imx_iomux_v3_setup_multiple_pads(peri_3v3_pads, + ARRAY_SIZE(peri_3v3_pads)); + + /* Active high for ncp692 */ + gpio_direction_output(IMX_GPIO_NR(4, 16) , 1); + +#ifdef CONFIG_SYS_I2C_MXC + setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); +#endif + + return 0; +} + +static int get_board_value(void) +{ + int r184, r185; + + imx_iomux_v3_setup_multiple_pads(board_recognition_pads, + ARRAY_SIZE(board_recognition_pads)); + + gpio_direction_input(IMX_GPIO_NR(4, 13)); + gpio_direction_input(IMX_GPIO_NR(4, 0)); + + r184 = gpio_get_value(IMX_GPIO_NR(4, 13)); + r185 = gpio_get_value(IMX_GPIO_NR(4, 0)); + + /* + * Machine selection - + * Machine r184, r185 + * --------------------------------- + * Basic 0 0 + * Basic Ks 0 1 + * Full 1 0 + * Extended 1 1 + */ + + return (r184 << 1) + r185; +} + +int board_early_init_f(void) +{ + setup_iomux_uart(); + setup_fec(); + + return 0; +} + +static char *board_string(void) +{ + switch (get_board_value()) { + case UDOO_NEO_TYPE_BASIC: + return "BASIC"; + case UDOO_NEO_TYPE_BASIC_KS: + return "BASICKS"; + case UDOO_NEO_TYPE_FULL: + return "FULL"; + case UDOO_NEO_TYPE_EXTENDED: + return "EXTENDED"; + } + return "UNDEFINED"; +} + +int checkboard(void) +{ + printf("Board: UDOO Neo %s\n", board_string()); + return 0; +} + +int board_late_init(void) +{ +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + env_set("board_name", board_string()); +#endif + + return 0; +} + +#ifdef CONFIG_SPL_BUILD + +#include <linux/libfdt.h> +#include <asm/arch/mx6-ddr.h> + +static const struct mx6sx_iomux_ddr_regs mx6_ddr_ioregs = { + .dram_dqm0 = 0x00000028, + .dram_dqm1 = 0x00000028, + .dram_dqm2 = 0x00000028, + .dram_dqm3 = 0x00000028, + .dram_ras = 0x00000020, + .dram_cas = 0x00000020, + .dram_odt0 = 0x00000020, + .dram_odt1 = 0x00000020, + .dram_sdba2 = 0x00000000, + .dram_sdcke0 = 0x00003000, + .dram_sdcke1 = 0x00003000, + .dram_sdclk_0 = 0x00000030, + .dram_sdqs0 = 0x00000028, + .dram_sdqs1 = 0x00000028, + .dram_sdqs2 = 0x00000028, + .dram_sdqs3 = 0x00000028, + .dram_reset = 0x00000020, +}; + +static const struct mx6sx_iomux_grp_regs mx6_grp_ioregs = { + .grp_addds = 0x00000020, + .grp_ddrmode_ctl = 0x00020000, + .grp_ddrpke = 0x00000000, + .grp_ddrmode = 0x00020000, + .grp_b0ds = 0x00000028, + .grp_b1ds = 0x00000028, + .grp_ctlds = 0x00000020, + .grp_ddr_type = 0x000c0000, + .grp_b2ds = 0x00000028, + .grp_b3ds = 0x00000028, +}; + +static const struct mx6_mmdc_calibration neo_mmcd_calib = { + .p0_mpwldectrl0 = 0x000E000B, + .p0_mpwldectrl1 = 0x000E0010, + .p0_mpdgctrl0 = 0x41600158, + .p0_mpdgctrl1 = 0x01500140, + .p0_mprddlctl = 0x3A383E3E, + .p0_mpwrdlctl = 0x3A383C38, +}; + +static const struct mx6_mmdc_calibration neo_basic_mmcd_calib = { + .p0_mpwldectrl0 = 0x001E0022, + .p0_mpwldectrl1 = 0x001C0019, + .p0_mpdgctrl0 = 0x41540150, + .p0_mpdgctrl1 = 0x01440138, + .p0_mprddlctl = 0x403E4644, + .p0_mpwrdlctl = 0x3C3A4038, +}; + +/* MT41K256M16 */ +static struct mx6_ddr3_cfg neo_mem_ddr = { + .mem_speed = 1600, + .density = 4, + .width = 16, + .banks = 8, + .rowaddr = 15, + .coladdr = 10, + .pagesz = 2, + .trcd = 1375, + .trcmin = 4875, + .trasmin = 3500, +}; + +/* MT41K128M16 */ +static struct mx6_ddr3_cfg neo_basic_mem_ddr = { + .mem_speed = 1600, + .density = 2, + .width = 16, + .banks = 8, + .rowaddr = 14, + .coladdr = 10, + .pagesz = 2, + .trcd = 1375, + .trcmin = 4875, + .trasmin = 3500, +}; + +static void ccgr_init(void) +{ + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + writel(0xFFFFFFFF, &ccm->CCGR0); + writel(0xFFFFFFFF, &ccm->CCGR1); + writel(0xFFFFFFFF, &ccm->CCGR2); + writel(0xFFFFFFFF, &ccm->CCGR3); + writel(0xFFFFFFFF, &ccm->CCGR4); + writel(0xFFFFFFFF, &ccm->CCGR5); + writel(0xFFFFFFFF, &ccm->CCGR6); + writel(0xFFFFFFFF, &ccm->CCGR7); +} + +static void spl_dram_init(void) +{ + int board = get_board_value(); + + struct mx6_ddr_sysinfo sysinfo = { + .dsize = 1, /* width of data bus: 1 = 32 bits */ + .cs_density = 24, + .ncs = 1, + .cs1_mirror = 0, + .rtt_wr = 2, + .rtt_nom = 2, /* RTT_Nom = RZQ/2 */ + .walat = 1, /* Write additional latency */ + .ralat = 5, /* Read additional latency */ + .mif3_mode = 3, /* Command prediction working mode */ + .bi_on = 1, /* Bank interleaving enabled */ + .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ + .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ + }; + + mx6sx_dram_iocfg(32, &mx6_ddr_ioregs, &mx6_grp_ioregs); + if (board == UDOO_NEO_TYPE_BASIC || board == UDOO_NEO_TYPE_BASIC_KS) + mx6_dram_cfg(&sysinfo, &neo_basic_mmcd_calib, + &neo_basic_mem_ddr); + else + mx6_dram_cfg(&sysinfo, &neo_mmcd_calib, &neo_mem_ddr); +} + +void board_init_f(ulong dummy) +{ + ccgr_init(); + + /* setup AIPS and disable watchdog */ + arch_cpu_init(); + + board_early_init_f(); + + /* setup GP timer */ + timer_init(); + + /* UART clocks enabled and gd valid - init serial console */ + preloader_console_init(); + + /* DDR initialization */ + spl_dram_init(); + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + /* load/boot image from boot device */ + board_init_r(NULL, 0); +} + +#endif |