diff options
Diffstat (limited to 'roms/u-boot/board/xilinx/Kconfig')
| -rw-r--r-- | roms/u-boot/board/xilinx/Kconfig | 83 |
1 files changed, 83 insertions, 0 deletions
diff --git a/roms/u-boot/board/xilinx/Kconfig b/roms/u-boot/board/xilinx/Kconfig new file mode 100644 index 000000000..64507b5d8 --- /dev/null +++ b/roms/u-boot/board/xilinx/Kconfig @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: GPL-2.0 +# +# Copyright (c) 2018, Luca Ceresoli <luca@lucaceresoli.net> + +if ARCH_ZYNQ || ARCH_ZYNQMP + +config XILINX_PS_INIT_FILE + string "Zynq/ZynqMP PS init file(s) location" + help + On Zynq and ZynqMP U-Boot SPL (or U-Boot proper if + ZYNQMP_PSU_INIT_ENABLED is set) is responsible for some + basic initializations, such as enabling peripherals and + configuring pinmuxes. The PS init file (called + psu_init_gpl.c on ZynqMP, ps7_init_gpl.c for Zynq-7000) + contains the code for such initializations. + + U-Boot contains PS init files for some boards, but each of + them describes only one specific configuration. Users of a + different board, or needing a different configuration, can + generate custom files using the Xilinx development tools. + + There are three ways to give a PS init file to U-Boot: + + 1. Set this variable to the path, either relative to the + source tree or absolute, where the psu_init_gpl.c or + ps7_init_gpl.c file is located. U-Boot will build this + file. + + 2. If you leave an empty string here, U-Boot will use + board/xilinx/zynq/$(CONFIG_DEFAULT_DEVICE_TREE)/ps7_init_gpl.c + for Zynq-7000, or + board/xilinx/zynqmp/$(CONFIG_DEFAULT_DEVICE_TREE)/psu_init_gpl.c + for ZynqMP. + + 3. If the above file does not exist, U-Boot will use + board/xilinx/zynq/ps7_init_gpl.c for Zynq-7000, or + board/xilinx/zynqmp/psu_init_gpl.c for ZynqMP. This file + is not provided by U-Boot, you have to copy it there + before the build. + +endif + +config XILINX_OF_BOARD_DTB_ADDR + hex "Default DTB pickup address" + default 0x1000 if ARCH_VERSAL + default 0x100000 if ARCH_ZYNQ || ARCH_ZYNQMP + depends on OF_BOARD || OF_SEPARATE + help + Offset in the memory where the board configuration DTB is placed. + +config BOOT_SCRIPT_OFFSET + hex "Boot script offset" + depends on ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL || MICROBLAZE + default 0xFC0000 if ARCH_ZYNQ || MICROBLAZE + default 0x3E80000 if ARCH_ZYNQMP + default 0x7F80000 if ARCH_VERSAL + help + Specifies distro boot script offset in NAND/QSPI/NOR flash. + +config ZYNQ_MAC_IN_EEPROM + bool "Reading MAC address from EEPROM" + help + Enable this option if your MAC address is saved in eeprom and + xlnx,eeprom DT property in chosen node points to it. + +if ZYNQ_MAC_IN_EEPROM + +config ZYNQ_GEM_I2C_MAC_OFFSET + hex "Set the I2C MAC offset" + default 0x0 + depends on DM_I2C + help + Set the MAC offset for i2C. + +endif + +config CMD_FRU + bool "FRU information for product" + help + This option enables FRU commands to capture and display FRU + information present in the device. The FRU Information is used + to primarily to provide "inventory" information about the boards + that the FRU Information Device is located on. |