diff options
Diffstat (limited to 'roms/u-boot/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c')
| -rw-r--r-- | roms/u-boot/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 302 |
1 files changed, 302 insertions, 0 deletions
diff --git a/roms/u-boot/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/roms/u-boot/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c new file mode 100644 index 000000000..8cb2808e0 --- /dev/null +++ b/roms/u-boot/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c @@ -0,0 +1,302 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2007-2008 + * Stelian Pop <stelian@popies.net> + * Lead Tech Design <www.leadtechdesign.com> + */ + +#include <common.h> +#include <debug_uart.h> +#include <init.h> +#include <net.h> +#include <vsprintf.h> +#include <asm/global_data.h> +#include <asm/io.h> +#include <asm/arch/clk.h> +#include <asm/arch/at91sam9g45_matrix.h> +#include <asm/arch/at91sam9_smc.h> +#include <asm/arch/at91_common.h> +#include <asm/arch/gpio.h> +#include <asm/arch/clk.h> +#include <lcd.h> +#include <linux/mtd/rawnand.h> +#include <atmel_lcdc.h> +#include <asm/mach-types.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* ------------------------------------------------------------------------- */ +/* + * Miscelaneous platform dependent initialisations + */ + +#ifdef CONFIG_CMD_NAND +void at91sam9m10g45ek_nand_hw_init(void) +{ + struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; + struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; + unsigned long csa; + + /* Enable CS3 */ + csa = readl(&matrix->ebicsa); + csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA; + writel(csa, &matrix->ebicsa); + + /* Configure SMC CS3 for NAND/SmartMedia */ + writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[3].setup); + writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(3) | + AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(2), + &smc->cs[3].pulse); + writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(4), + &smc->cs[3].cycle); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | +#ifdef CONFIG_SYS_NAND_DBW_16 + AT91_SMC_MODE_DBW_16 | +#else /* CONFIG_SYS_NAND_DBW_8 */ + AT91_SMC_MODE_DBW_8 | +#endif + AT91_SMC_MODE_TDF_CYCLE(3), + &smc->cs[3].mode); + + at91_periph_clk_enable(ATMEL_ID_PIOC); + + /* Configure RDY/BSY */ + at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); + + /* Enable NandFlash */ + at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); +} +#endif + +#if defined(CONFIG_SPL_BUILD) +#include <spl.h> +#include <nand.h> + +void at91_spl_board_init(void) +{ + /* + * On the at91sam9m10g45ek board, the chip wm9711 stays in the + * test mode, so it needs do some action to exit test mode. + */ + at91_periph_clk_enable(ATMEL_ID_PIODE); + at91_set_gpio_output(AT91_PIN_PD7, 0); + at91_set_gpio_output(AT91_PIN_PD8, 0); + at91_set_pio_pullup(AT91_PIO_PORTD, 7, 1); + at91_set_pio_pullup(AT91_PIO_PORTD, 8, 1); + +#ifdef CONFIG_SD_BOOT + at91_mci_hw_init(); +#elif CONFIG_NAND_BOOT + at91sam9m10g45ek_nand_hw_init(); +#endif +} + +#include <asm/arch/atmel_mpddrc.h> +static void ddr2_conf(struct atmel_mpddrc_config *ddr2) +{ + ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM); + + ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 | + ATMEL_MPDDRC_CR_NR_ROW_14 | + ATMEL_MPDDRC_CR_DQMS_SHARED | + ATMEL_MPDDRC_CR_CAS_DDR_CAS3); + + ddr2->rtr = 0x24b; + + ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */ + 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */ + 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */ + 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 60 ns */ + 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */ + 1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/ + 1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */ + 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */ + + ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */ + 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET | + 16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET | + 14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET); + + ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET | + 0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET | + 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET | + 2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET); +} + +void mem_init(void) +{ + struct atmel_mpddrc_config ddr2; + + ddr2_conf(&ddr2); + + at91_system_clk_enable(AT91_PMC_DDR); + + /* DDRAM2 Controller initialize */ + ddr2_init(ATMEL_BASE_DDRSDRC0, ATMEL_BASE_CS6, &ddr2); +} +#endif + +#ifdef CONFIG_CMD_USB +static void at91sam9m10g45ek_usb_hw_init(void) +{ + at91_periph_clk_enable(ATMEL_ID_PIODE); + + at91_set_gpio_output(AT91_PIN_PD1, 0); + at91_set_gpio_output(AT91_PIN_PD3, 0); +} +#endif + +#ifdef CONFIG_LCD + +vidinfo_t panel_info = { + .vl_col = 480, + .vl_row = 272, + .vl_clk = 9000000, + .vl_sync = ATMEL_LCDC_INVLINE_NORMAL | + ATMEL_LCDC_INVFRAME_NORMAL, + .vl_bpix = 3, + .vl_tft = 1, + .vl_hsync_len = 45, + .vl_left_margin = 1, + .vl_right_margin = 1, + .vl_vsync_len = 1, + .vl_upper_margin = 40, + .vl_lower_margin = 1, + .mmio = ATMEL_BASE_LCDC, +}; + + +void lcd_enable(void) +{ + at91_set_A_periph(AT91_PIN_PE6, 1); /* power up */ +} + +void lcd_disable(void) +{ + at91_set_A_periph(AT91_PIN_PE6, 0); /* power down */ +} + +static void at91sam9m10g45ek_lcd_hw_init(void) +{ + at91_set_A_periph(AT91_PIN_PE0, 0); /* LCDDPWR */ + at91_set_A_periph(AT91_PIN_PE2, 0); /* LCDCC */ + at91_set_A_periph(AT91_PIN_PE3, 0); /* LCDVSYNC */ + at91_set_A_periph(AT91_PIN_PE4, 0); /* LCDHSYNC */ + at91_set_A_periph(AT91_PIN_PE5, 0); /* LCDDOTCK */ + + at91_set_A_periph(AT91_PIN_PE7, 0); /* LCDD0 */ + at91_set_A_periph(AT91_PIN_PE8, 0); /* LCDD1 */ + at91_set_A_periph(AT91_PIN_PE9, 0); /* LCDD2 */ + at91_set_A_periph(AT91_PIN_PE10, 0); /* LCDD3 */ + at91_set_A_periph(AT91_PIN_PE11, 0); /* LCDD4 */ + at91_set_A_periph(AT91_PIN_PE12, 0); /* LCDD5 */ + at91_set_A_periph(AT91_PIN_PE13, 0); /* LCDD6 */ + at91_set_A_periph(AT91_PIN_PE14, 0); /* LCDD7 */ + at91_set_A_periph(AT91_PIN_PE15, 0); /* LCDD8 */ + at91_set_A_periph(AT91_PIN_PE16, 0); /* LCDD9 */ + at91_set_A_periph(AT91_PIN_PE17, 0); /* LCDD10 */ + at91_set_A_periph(AT91_PIN_PE18, 0); /* LCDD11 */ + at91_set_A_periph(AT91_PIN_PE19, 0); /* LCDD12 */ + at91_set_B_periph(AT91_PIN_PE20, 0); /* LCDD13 */ + at91_set_A_periph(AT91_PIN_PE21, 0); /* LCDD14 */ + at91_set_A_periph(AT91_PIN_PE22, 0); /* LCDD15 */ + at91_set_A_periph(AT91_PIN_PE23, 0); /* LCDD16 */ + at91_set_A_periph(AT91_PIN_PE24, 0); /* LCDD17 */ + at91_set_A_periph(AT91_PIN_PE25, 0); /* LCDD18 */ + at91_set_A_periph(AT91_PIN_PE26, 0); /* LCDD19 */ + at91_set_A_periph(AT91_PIN_PE27, 0); /* LCDD20 */ + at91_set_B_periph(AT91_PIN_PE28, 0); /* LCDD21 */ + at91_set_A_periph(AT91_PIN_PE29, 0); /* LCDD22 */ + at91_set_A_periph(AT91_PIN_PE30, 0); /* LCDD23 */ + + at91_periph_clk_enable(ATMEL_ID_LCDC); + + gd->fb_base = CONFIG_AT91SAM9G45_LCD_BASE; +} + +#ifdef CONFIG_LCD_INFO +#include <nand.h> +#include <version.h> + +void lcd_show_board_info(void) +{ + ulong dram_size, nand_size; + int i; + char temp[32]; + + lcd_printf ("%s\n", U_BOOT_VERSION); + lcd_printf ("(C) 2008 ATMEL Corp\n"); + lcd_printf ("at91support@atmel.com\n"); + lcd_printf ("%s CPU at %s MHz\n", + ATMEL_CPU_NAME, + strmhz(temp, get_cpu_clk_rate())); + + dram_size = 0; + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) + dram_size += gd->bd->bi_dram[i].size; + nand_size = 0; + for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) + nand_size += get_nand_dev_by_index(i)->size; + lcd_printf (" %ld MB SDRAM, %ld MB NAND\n", + dram_size >> 20, + nand_size >> 20 ); +} +#endif /* CONFIG_LCD_INFO */ +#endif + +#ifdef CONFIG_DEBUG_UART_BOARD_INIT +void board_debug_uart_init(void) +{ + at91_seriald_hw_init(); +} +#endif + +#ifdef CONFIG_BOARD_EARLY_INIT_F +int board_early_init_f(void) +{ +#ifdef CONFIG_DEBUG_UART + debug_uart_init(); +#endif + return 0; +} +#endif + +int board_init(void) +{ + /* arch number of AT91SAM9M10G45EK-Board */ +#ifdef CONFIG_AT91SAM9M10G45EK + gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9M10G45EK; +#elif defined CONFIG_AT91SAM9G45EKES + gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G45EKES; +#endif + + /* adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + +#ifdef CONFIG_CMD_NAND + at91sam9m10g45ek_nand_hw_init(); +#endif +#ifdef CONFIG_CMD_USB + at91sam9m10g45ek_usb_hw_init(); +#endif +#ifdef CONFIG_LCD + at91sam9m10g45ek_lcd_hw_init(); +#endif + return 0; +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size((void *) CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); + return 0; +} + +#ifdef CONFIG_RESET_PHY_R +void reset_phy(void) +{ +} +#endif |