diff options
Diffstat (limited to 'roms/u-boot/board/spear/x600/x600.c')
| -rw-r--r-- | roms/u-boot/board/spear/x600/x600.c | 150 |
1 files changed, 150 insertions, 0 deletions
diff --git a/roms/u-boot/board/spear/x600/x600.c b/roms/u-boot/board/spear/x600/x600.c new file mode 100644 index 000000000..9c30581ec --- /dev/null +++ b/roms/u-boot/board/spear/x600/x600.c @@ -0,0 +1,150 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2009 + * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. + * + * Copyright (C) 2012 Stefan Roese <sr@denx.de> + */ + +#include <common.h> +#include <flash.h> +#include <init.h> +#include <micrel.h> +#include <nand.h> +#include <net.h> +#include <netdev.h> +#include <phy.h> +#include <rtc.h> +#include <asm/io.h> +#include <asm/mach-types.h> +#include <asm/arch/hardware.h> +#include <asm/arch/spr_defs.h> +#include <asm/arch/spr_misc.h> +#include <linux/mtd/fsmc_nand.h> +#include "fpga.h" + +static struct nand_chip nand_chip[CONFIG_SYS_MAX_NAND_DEVICE]; + +int board_init(void) +{ + /* + * X600 is equipped with an M41T82 RTC. This RTC has the + * HT bit (Halt Update), which needs to be cleared upon + * power-up. Otherwise the RTC is halted. + */ + rtc_reset(); + + return spear_board_init(MACH_TYPE_SPEAR600); +} + +int board_late_init(void) +{ + /* + * Monitor and env protection on by default + */ + flash_protect(FLAG_PROTECT_SET, + CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + + CONFIG_SYS_SPL_LEN + CONFIG_SYS_MONITOR_LEN + + 2 * CONFIG_ENV_SECT_SIZE - 1, + &flash_info[0]); + + /* Init FPGA subsystem */ + x600_init_fpga(); + + return 0; +} + +/* + * board_nand_init - Board specific NAND initialization + * @nand: mtd private chip structure + * + * Called by nand_init_chip to initialize the board specific functions + */ + +void board_nand_init(void) +{ + struct misc_regs *const misc_regs_p = + (struct misc_regs *)CONFIG_SPEAR_MISCBASE; + struct nand_chip *nand = &nand_chip[0]; + + if (!(readl(&misc_regs_p->auto_cfg_reg) & MISC_NANDDIS)) + fsmc_nand_init(nand); +} + +int board_phy_config(struct phy_device *phydev) +{ + unsigned short id1, id2; + + /* check whether KSZ9031 or AR8035 has to be configured */ + id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2); + id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3); + + if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) { + /* PHY configuration for Micrel KSZ9031 */ + printf("PHY KSZ9031 detected - "); + + phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000, 0x1c00); + + /* control data pad skew - devaddr = 0x02, register = 0x04 */ + ksz9031_phy_extended_write(phydev, 0x02, + MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW, + MII_KSZ9031_MOD_DATA_NO_POST_INC, + 0x0000); + /* rx data pad skew - devaddr = 0x02, register = 0x05 */ + ksz9031_phy_extended_write(phydev, 0x02, + MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, + MII_KSZ9031_MOD_DATA_NO_POST_INC, + 0x0000); + /* tx data pad skew - devaddr = 0x02, register = 0x05 */ + ksz9031_phy_extended_write(phydev, 0x02, + MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, + MII_KSZ9031_MOD_DATA_NO_POST_INC, + 0x0000); + /* gtx and rx clock pad skew - devaddr = 0x02, reg = 0x08 */ + ksz9031_phy_extended_write(phydev, 0x02, + MII_KSZ9031_EXT_RGMII_CLOCK_SKEW, + MII_KSZ9031_MOD_DATA_NO_POST_INC, + 0x03FF); + } else { + /* PHY configuration for Vitesse VSC8641 */ + printf("PHY VSC8641 detected - "); + + /* Extended PHY control 1, select GMII */ + phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020); + + /* Software reset necessary after GMII mode selction */ + phy_reset(phydev); + + /* Enable extended page register access */ + phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001); + + /* 17e: Enhanced LED behavior, needs to be written twice */ + phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff); + phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff); + + /* 16e: Enhanced LED method select */ + phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea); + + /* Disable extended page register access */ + phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000); + + /* Enable clock output pin */ + phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049); + } + + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} + +int board_eth_init(struct bd_info *bis) +{ + int ret = 0; + + if (designware_initialize(CONFIG_SPEAR_ETHBASE, + PHY_INTERFACE_MODE_GMII) >= 0) + ret++; + + return ret; +} |